The piston rod of diameter 30mm and length 800mm in a hydraulic cylinder is subjected to a compressive force of 10 kN due to the internal pressure. The end conditions for the rod may be assumed as guided at the piston end and hinged at the other end. The Young's modulus is 200GPa. Calculate its factor of safety for the piston rod?

The piston rod of diameter 30mm and length 800mm in a hydraulic cylinder is subjected to a compressive force of 10 kN due to the internal pressure. The end conditions for the rod may be assumed as guided at the piston end and hinged at the other end. The Young's modulus is 200GPa. Calculate its factor of safety for the piston rod?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.7P: The linkage is made of two homogenous bars of weights shown in the figure. Determine the horizontal...

See similar textbooks

Similar questions

The bar is 10m long. A mass of 40kg places at 9m from left end of bar. Where should a 60kg mass be placed to balance the bar?
An aquarium tank holds salt water (RD 1.015) to a depth of 2.9 metres and has sides inclined at 75o to the horizontal. An access door A-B, measuring 1.1 metres by 1.1 metres, is pivoted at the base of the door (B) and held shut by a bolt at the top of the door (A). What is the tensile force in the bolt at point A.
The ABC lever is supported at point A and connected to a short connection BD as shown in Fig.5-22a. If the weight of the members is insignificant, determine the force of the pin on the lever at A.
The Cylinder weighs 1000 kg, rest on an plane which is inclined at 34° from the horizontal. The normal force acting on a plane to the cylinder is 10 KN. Assume smooth surface, the cylinder leaned to a vertical rod of 8m long and has a weight of 5 KN which was supported by a cable and a hinged (as shown). Find the tensile force of the cable holding the rod and the reactions of hinged to support the cylinder from sliding.
I need to draw a free body diagram and the solution m2=88kg
The thick walled cylinder of a hydraulic system is acted by a hydraulic pressure of 370 psi while themaximum load of the piston is 5500 lbs. If the allowable tensile stress is 2 ksi, find the required wallthickness of the cylinder.
A cylindrical pressure vessel has an inner diameter of 4 ft and a thicknessof 1 2 in. Determine the maximum internal pressure it can sustain so that neither its circumferential nor its longitudinal stress component exceeds 20 ksi. Under the same conditions, what is the maximum internal pressure that a similar-size spherical vessel can sustain?
Find the Young’s modulus (Y) of the steel rod of 1 m long and a cross sectional area of 0.05 cm2, elongates 2% when supported by a 120 kg load, hung from the other end.
Is this statement true? i) A practical rigid body does exist.
Complete solution with free body diagram pls
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.