The power loss in an overhead transmission line would increases when the of the line is increases. А. inductance and capacitance В. resistance С. resistance and inductance D. resistance, inductance and capacitance

The power loss in an overhead transmission line would increases when the of the line is increases. А. inductance and capacitance В. resistance С. resistance and inductance D. resistance, inductance and capacitance

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.11P: A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of...

See similar textbooks

Related questions

Q: If Voltage regulation of Transmission line increases Efficiency will decreases Select one: True…

A: Choose the correct option If the voltage regulation of transmission line increase, efficiency will…

Q: 30) In a lightly loaded long distance EHV lines, line loading is and hasan may power factor: (A)…

A: EHV lines transport significant quantities of energy across long distances. The lesser the losses,…

Q: Transmission line with a load Zl = 100 + i80 ohm with characteristic impedance of Z0 = 5 ohm is…

A: Given data Load impedance ZL=(100+j80)Ω Characteristics impedance Z0=75Ω Operating frequency…

Q: Need to validate my answers for item 3

Q: (i)A 3-phase line has conductors 5 cm in diameter spaced equilaterally 2 m apart. If the dielectric…

Q: 6. A single-phase 50 Hz generator supplies an inductive load of 5000 k W at a power factor of 0.707…

A: NOTE- “Since you have posted a question with multiple sub-parts, we will solve first three subparts…

Q: Practice Problem 1: Given that Vbn = 110/30°, find Van and Ven, assuming a positive (abc) sequence.

A: Given data, Vbn=110∠300

Q: A 100MHZ generator with V=1020° (V) and internal resistance 502 is connected to g lossless 502 air…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Example 6.3 A 60-Hz, 230-km, three-phase overhead transmission line has a series impedance z =…

A: Given:impedance, z =0.8431 < 79.04°Ω/kmshunt addmiran y = 5.105×106<90 °s/kmf = 60 Hzlength…

Q: The A and C constants of a medium length transmission line is 0.936 + j0.016 ohms and (-5.18 + j914)…

A: Basic problem on transmission line in power system.

Q: Problem 3: A voltage generator with v, (t) = 5 cos(2n × 10°t) V and internal impedance Zą =50 N…

A: (a):Γ=ZL-Z0ZL+Z0Γ=100-j100-50100-j100+50Γ=50-j100150-j100Γ=0.62e-j29.7'

Q: Q1: The parameters of long three-phase transmission line 200 km with 50 Hz are l = 1.3 mH/km, c = 9…

A: Given length of the line, l=200km. The impedance per unit is calculated as

Q: A 132 kV, 60 Hz transmission line has the following generalized constants: A=0.9696 20.49° B=52.88…

Q: j0.1 2.0+j0.5 j0.4 j0.2 1.01 3.

A: This question is from "Power System". Under which we are going to find out the "Y-parameter of the…

Q: A ( single phase transmission line 100 km long has the following constants Resistance/km 0 · 25 Ω…

A: Dear student as per our guidelines we are supposed to solve only one question in which it should…

Q: The Primary constants for a certain transmission line operating at 7.5 KHz PRIMARY CONSTANT VALUE R…

A: Given:f=7.5 KHzR=2.6Ω/KmL=2.4 mH/Km C=0.0078 µF/KmG=0.11 µohms/KmLength of line=50 KmGenerator…

Q: Q1) A transmission line which operates at 1MHz, is formed by the following line parameters: R= 5 Ω,…

A: Characteristics impedance, ZC: It is the impedance offered by apparatus for surges or travelling…

Q: Question.2(b):A transmission line has a characteristic impedance of 80 ohms and a parallel…

A: In this question we need to find a series Inductance of the transmission line.

Q: 4.41 Calculate the capacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the line…

Q: 1. A real load of ZL = 100 is attached to 50 2 line, insert a matching circuit of two- section using…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Example 1.2 The characteristic impedance of a uniform transmission line is 2000 ohm at frequency of…

Q: A transmission line is delivering a load of 40 MW at 110 kV and 80% lagging power factor. If the…

A: Types of Power Transmission line Short Transmission line Medium Transmission line Long Transmission…

Q: Problem 4. A 220-kV, three-phase transmission line has a per phase series impedance z = 0.005 +…

Q: A telephone line has following parameters: L=0.2pH/m, C=0.5nF/m, G=400pS/m and R=400/m. (a) If the…

A: Given R = 40 ohm/m, G = 400 micro S/m, C = 0.5 n F/m, L = 0.2 micro H/m, Calculating characteristic…

Q: d, a) Pi-Model of this transmission line. b) Efficiency of the line (n%).

Q: A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0.85 p.f. lagging by means of a…

A: Given A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0-85 p.f. lagging by means of a…

Q: Theoretical Impedance Admittance Transmission Parameters Parameters Parameters yı1 A Z12 y12 В y22 D

Q: 3. b) For a certain transmission lines, if l=50m and ta2=400nsec, then Vp will equal to: 1. 125*10°…

Q: ) The Primary constants for a certain transmission line operating at 7.5 KHz PRIMARY CONSTANT VALUE…

A: 1.Part a) :- The characteristic impedance of a transmission line is given by :- Z = R + jωLG + jωC…

Q: What are the factors which governs the performance of transmission line? Write a short answer.

A: Main factor which governs the transmission line is: Voltage regulation Efficiency Losses

Q: 1 A short circuited transmission line of Zo 50 S2 is fed with a 250 V generator. Internal impedance…

A: By using the concept of transmission lines we need to calculate the value of current at the short…

Q: The one line diagram of a four-bus system is shown to the right. The line impedances are given in…

A: Given V1 =1∠0° V3 =1.02P3 =0.9

Q: a) Line head current, b) Line head voltage, c) Calculate the percent voltage regulation. (Line…

Q: The ABCD constants of a three-phase, 345-kV transmission line are A = D = 0.98182 + j0.0012447 B =…

A: In this question, The ABCD constants of a three-phase, 345-kV transmission line are A = D =…

Q: The shunt admittance and series impedance of a long transmission line are given with respect to…

Q: 6. A single-phase 50 Hz generator supplies an inductive load of 5000 kW at a power factor of 0.707…

A: Total resistance of the line, R= 20*0.0195 = 0.39Ω…

Q: 5. A single-phase 50 Hz generator supplies an inductive load of 5000 kW at a power factor of 0.707…

Q: Lossless transmission line of 0.25 2 having Z, = 100 N terminated by load impedance of ZL = 40 + j…

Q: Q) A transmission line of 300 Km long having a resistance of 10.4 OKm ,a capacitance of 0.00835…

A: A transmission line is used for the transmission of electrical power from generating substation to…

Q: Question.2(b):A transmission line has a characteristic impedance of 40 ohms and a parallel…

Q: For the given power transfer, a star system is associated with larger line currents and a delta…

A: Given statement, For the given power transfer a star system is associated with large line currents…

Q: Alternating Current is preferred over Direct Current in Power System, Why?

A: e) Alternating Current is preferred over Direct Current in Power System Why ?

Q: Question 1 For the power system shown below, the admittance of each transmission line is (2.941-…

A: To find V2 and δ2 and V3 and δ3 after first iteration.

Q: A transmission line is delivering a load of 40 MW at 110 kV and 80% lagging power factor. If the…

A: Types of Power Transmission line Short Transmission line Medium Transmission line Long Transmission…

Q: A 3-phase overhead transmission line has its coductors arranged at the cor- ners of an equilateral…

Q: Q1. The length of the short transmission line is 60 km, impedance of this line is given z = 0.12 +…

A: Given short transmission line. Total impedance Z=(0.12+j0.25)×60 Z=7.2+j 15

Q: the distribution of loads among the generating units is called as economic dispatch. Select one:…

A: Economic load dispatch in the power system is very important in optimizing loads among the…

Q: Shunt capacitors are installed at the receiving end to improve the line performance of a…

A: Determine the receiving total real power when the sending end voltage is 220 kV.

Q: * A 652 lossless transmission line has length 1= 52/2. It is terminated by a load impedance of Z, =…

A: First we will find out input impedance then we will find out power .

Q: Theoretical Admittance Transmission Impedance Parameters Parameters Parameters y11 A Z12 y12 В C y22…

A: It is given that: Z1 = 10 ohms Z2 = 25 ohms Z3 = 50 ohms Z4 = 75 ohms Z5 = 100 ohms Z6 = 75 ohms…

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

Please answer clearly

The power loss in an overhead transmission
line would increases when the
of
the line is increases.
А.
inductance and capacitance
В.
resistance
C. O
resistance and inductance
D.
resistance, inductance and capacitance

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of 0.15/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance. Using the short line model, find the sending-end voltage, voltage regulation, sending-end power, and transmission line efficiency when the line is supplying a three-phase load of (a) 381 MVA at 0.8 power factor lagging and at 220 kV and (b) 381 MVA at 0.8 power factor leading and at 220 kV.
Calculate the capacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the three-phase line in Problem 4.18. Also calculate the line-charging current in kA/phase if the line is 110 km in length and is operated at 230 kV. Neglect the effect of the earth plane.
With generator conyention, where the current leaves the positive terminal of the circuit element, if P is positive then positive real power is delivered. (a) False (b) True
The units of admittance, conductance, and susceptance are siemens. (a) True (b) False
470 kVA load at 12 kV. Its resistance is 7 Ω and inductive reactance is 7 Ω if the load power factor is 0.9 lagging. Determine the Current through the line , Sending end voltage , Sending end power factor , Regulation of transmission line , Efficiency of transmission line Note:please do not handwriting
1)Write the Installed Generation Capacity of Sultanate of Oman with current energy share of Conventional and Non-Conventional Energy Sources. 2) Why the Capacitance effect is neglected in Short Transmission Line. 3) Distinguish between Lumped or Distributed elements in a Transmission Line.
A single phase transmission line is delivering 470 kVA load at 12 kV. Its resistance is 6 Ω and inductive reactance is 6 Ω if the load power factor is 0.7 lagging. Determine the 1- Current through the line? 2- Sending end voltage? 3- Sending end power factor? 4- Regulation of transmission line? 5-Efficiency of transmission line?
Give the physical significance of the generalized circuit constant A,B,C and D of a transmission line. Find the values of A, B, C, D in the following approximate methods in terms of Z and Y (i)simple series impedance method (ii) nominal π method (iii) nominal T method
Estimate the distance over which a load of 15000 kW at 0·85 p.f. can be delivered by a 3-phase transmission line having conductors of steel-cored aluminum each of resistance 0·905 Ω/phase per kilometer. The voltage at the receiving end is to be 132 kV and the loss in transmission is to be 7·5% of the load.
An 11 KV, 3-phase transmission line has a resistance of 1.5 Ω and reactance of 4 Ω per phase.Calculate the percentage regulation and efficiency of the line when a total load of 5000 KVA at 0.8 lagging power factor is applied at 11KV at the distant end.
A high voltage DC transmission line delivers 1000 MW at 500 kV to an aggregate load over a distance of 900 km. Determine the voltage at the sending end. Assume the loop resistance of the line to be 1mΩ
50 km of single-phase transmission line, 800 kVA power 8 kV, is carried with 0.9 reverse power factor. The resistance of one kilometer of the line is 42 mΩ, and the reactance of one kilometer of the line is 0.646 Ω. Find the voltage at the beginning of the line and the efficiency of the line accordingly.