Give the physical significance of the generalized circuit constant A,B,C and D of a transmission line. Find the values of A, B, C, D in the following approximate methods in terms of Z and Y (i)simple series impedance method (ii) nominal π method (iii) nominal T method

Give the physical significance of the generalized circuit constant A,B,C and D of a transmission line. Find the values of A, B, C, D in the following approximate methods in terms of Z and Y (i)simple series impedance method (ii) nominal π method (iii) nominal T method

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.20P

See similar textbooks

Related questions

Q: Formulate the ???? matrix for the network shown here. 2. Modify ???? in the previous problem if the…

A: Redraw the circuit Given values : Y1-3 = j0.30Y1-2 = j0.24Y2-3 = j0.16 Z1-2 = j0.20Z2-3 =…

Q: A 230-kV, 100-km, 60-Hz three-phase overhead transmission line with a rated current of 900 A/phase…

A: Transmission line- The term transmission line refers to both overhead and underground cables. An…

Q: Q4: A 3-phase, 50Hz, 150 km line has a resistance, inductive reactance and capacitive shunt…

Q: A 60-Hz, 110-mile, three-phase overhead transmission line, constructed of ACSR conductors, has a…

Q: )A 60-ohm distortionless transmission line has a capacitance of 0.15nF/m. The…

A: here, the given line is the distortionless transmission line so, the condition of the distortionless…

Q: 1. A 69-kV (L-L), three-phase short transmission line is 16 km long. The line has a per phase series…

A: The solution is given below.

Q: A 735 kV, 300 km, balanced 3-phase lossless line. The line has the following series-impedance and…

A: It is given that: Vs=735 kV=750×103 VL=300 km=300×103 mx=0.2 Ω/kmb=4×10-6 S/km

Q: Calculate the voltage reflection coefficients at the terminating end of a transmission line with a…

A: Voltage reflection coefficient is determined based on characteristics impedence and load impedence…

Q: Q3/ A 3-phase, 50HZ, 150 km line has a resistance, inductive reactance and capacitive shunt…

A: Total resistance 'R' per phase of the line, R=0.1*150 =15Ω Total inductive reactance 'XL'…

Q: The ABCD constants of a lossless three-phase, 500-kV transmission line are A = D = 0.86 + j0 B = 0 +…

A: Solution (a) 3 Vr Ir =1000x106Ir = 1000 x106 x1033x500x103 =1154. 7 A (0.8-j0.6)Vs = AVr+BIr…

Q: A 3-ph transmission line has a total length of 200 km. This transmission line has a resistance of…

Q: A three-phase transmission line is 160 km long and supplies a load of 12 MW at 0.85 power factor…

A: i) Nominal T method- Total resistance, R=0.275*160 =44Ω Total inductive reactance, XL=0.5625*160…

Q: A 132-kV, 50HZ, three-phase transmission line has a per phase series impedance of z = 0.11 0/km and…

Q: b) Write ABCD Parameters of the nominal T model of the medium transmission line.

Q: In a mismatched transmission line with intrinsic impedance of Z, and with a load of impedance of Z,…

A: A quarter-wave transformer is a basic impedance transformer used in impedance matching to reduce…

Q: Q3/ A 3-phase, 50HZ, 150 km line has a resistance, inductive reactance and capacitive shunt…

Q: 3. A 210-km, 192-KV, 60 Hz three-phase line has a positive-sequence series impedance z= 0.06+j0.4…

A: The data given in the question are:…

Q: Q5: A 3-phase, 50Hz, 150 km line has a resistance, inductive reactance and capacitive shunt…

Q: A 3-ph, 50 Hz, 150 km line has resistance, inductive reactance and capacitive admittance of 0.1, 0.5…

Q: What is the difference between balanced and unbalanced line transmission lines, show the difference…

Q: A 210-km, 192-KV, 60 Hz three-phase line has a positive-sequence series impedance z= 0.06+j0.4 Q/km…

A: Explanation: a) The general expression for ABCD parameters is VSIS = ABCD VRIR ...(i) Length of the…

Q: Draw the equivalent circuit of long transmission line and derive the equations of sending end…

A: Types of Transmission line Long Transmission line Medium Transmission line Short Transmission…

Q: A 69-kV, three-phase short transmission line is 16 km long. The line has a per phase series…

Q: Question: A three-phase, 60-Hz, completely transposed 345-kV, 200-km line has line constants: z=…

Q: A 40-km, 220-kV, 60-Hz three-phase overhead transmission line has a per-phase resistance of 0.15…

Q: lossless transmission line has a capacitance per unit length of 64pF/m and an inductance per unit…

Q: Q3. A three-phase, 60-Hz, completely transposed 345-kV, 200-km line has the following…

A: Part (a): The total impedance experienced by the transmission line is given by: Z=0.01+j0.2 Ω/km200…

Q: ii) A 10% voltage drop occurs in 2 km of a uniformly loaded transmission line terminated by its…

Q: The open-circuit and short-circuit impedances measured at the input terminals of an air- spaced…

Q: A 3 phase, 50 Hz, 150 km line has a resistance, inductive reactance and capacitive shunt admittance…

Q: Example 3.3 A three-phase 765-kV, 60-Hz, 300-km, completely transposed line has the following…

Q: 7. A transmission line has the following per-unit-length parameters: L = 0.25 uH/m, C= 100 pF/m,…

Q: Find the short circuit current at the D point with the bus-admittance method of the system, whose…

A: Converting DELTA (BCD) into STAR

Q: km, and C=8.86nF/km. At full load, the line delivers 250MW at 0.9 pf lagging and 230 kV. Using the z…

A: All the values of R,L and C are given in per unit length. We will multiply them with total length…

Q: 3.) Identical series capacitors are installed in each phase at both ends of the line in #1 and…

A: Series compensation is used to improve the power transmitted through transmission lines. it…

Q: A distortionless transmission line has a resistance per unit length of 0.5 ohm/m. If the…

A: For a transmission line, the following line parameters are present: Since the given transmission…

Q: A 400kV, 200km, 3-phase transmssion line have the follollowing parameters per phase: z= 0.14+j0.304…

Q: For a given short transmission line of impedance R+jX ohms/phase, the sending end and receiving end…

A: Short transmission line Impedance Z=R+jX ohm/phase Sending end voltage Vs Receiving end voltages VR…

Q: A lossless transmission line having 50 Ω characteristic impedance and length λ/4 is short-circuited…

A: We know that the input impedance for a loss less transmission line for a quater wave λ4 is given…

Q: Question # 03: What is the difference between balanced and unbalanced line transmission lines, show…

A: Given: The difference between the transmission lines which are balanced and unbalanced is asked.

Q: Consider a scenario with 2 different Tx lines of length 45 km and 90 km connected at a common bus…

A: Since 45 km long transmission line operating at either 50 or 60 Hz falls under the…

Q: For a transmission line: a) Draw the lumped-element circuit model. b) State what each element of the…

Q: Write ‘T’ for True and ‘F’ for False: Constant A, B, C, D represents the voltage of a transmission

A: The explanation is as follows.

Q: ) Write ABCD Parameters of the nominal π model of the medium transmission line.

Q: 2. a) Draw nominal - T model of Transmission Line. ( b) Write ABCD Parameters of the nominal T model…

Q: a) Draw nominal - T model of Transmission Line. b) Write ABCD Parameters of the nominal T…

Q: Following are types of Transmission Lines EXCEPT A. Medium Line B. Long Line

A: In this question we will answer of transmission line questions....

Concept explainers

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: given data

VIEW

Step 2: solution

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of 0.15/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance. Using the short line model, find the sending-end voltage, voltage regulation, sending-end power, and transmission line efficiency when the line is supplying a three-phase load of (a) 381 MVA at 0.8 power factor lagging and at 220 kV and (b) 381 MVA at 0.8 power factor leading and at 220 kV.
A 30-km, 34.5-kV, 60-Hz, three-phase line has a positive-sequence series impedance z=0.19+j0.34/km. The load at the receiving end absorbs 10 MVA at 33 kV. Assuming a short line, calculate: (a) the ABCD parameters, (b) the sending-end voltage for a load power factor of 0.9 lagging, and (c) the sending-end voltage for a load power factor of 0.9 leading.
Calculate the capacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the three-phase line in Problem 4.18. Also calculate the line-charging current in kA/phase if the line is 110 km in length and is operated at 230 kV. Neglect the effect of the earth plane.
A 200-km, 230-kV, 60-Hz, three-phase line has a positive-sequence series impedance z=0.08+j0.48/km and a positive-sequence shunt admittance y=j3.33106S/km. At full load, the line delivers 250 MW at 0.99 p.f. lagging and at 220 k V. Using the nominal circuit, calculate: (a) the ABCD parameters, (b) the sending-end voltage and current, and (c) the percent voltage regulation.
A 350-km, 500-kV, 60-Hz, three-phase uncompensated line has a positive-sequence series reactance x=0.34/km and a positive-sequence shunt admittance y=j4.5106S/km. Neglecting losses, calculate: (a) Zc,. (b) l, (c) the ABCD parameters, (d) the wavelength of the line in kilometers, and (e) the surge impedance loading in MW.
Consider the transmission line of Problem 5.18. (a) Find the ABCD parameters of the line when uncompensated. (b) For a series capacitive compensation of 70 (35 at the sending end and 35 at the receiving end), determine the ABCD parameters. Comment on the relative change in the magnitude of the B parameter with respect to the relative changes in the magnitudes of the A, C, and D parameters Also comment on the maximum power that can be transmitted when series compensated.
The 500-kV, 60-Hz, three-phase line in Problems 4.20 and 4.41 has a 180-km length and delivers 1600 M W at 475 kv and at 0.95 power factor leading to the receiving end at full load. Using the nominal circuit, calculate the (a) ABCD parameters, (b) sending-end voltage and current, (c) sending-end power and power factor, (d) full-load line losses and efficiency, and (e) percent voltage regulation. Assume a 50C. conductor temperature to determine the resistance of this line.
The 100-km, 230-kV, 60-Hz, three-phase line in Problems 4.18 and 4.39 delivers 300 M VA at 218 kv to the receiving end at full load. Using the nominal circuit, calculate the ABCD parameters, sending-end voltage, and percent voltage regulation when the receiving-end power factor is (a) 0.9 lagging, (b) unity, and (c) 0.9 leading. Assume a 50C conductor temperature to determine the resistance of this line.
Representing a transmission line by the two-port network, in terms of ABCD parameters, (a) express VS, which is the sending-end voltage, in terms of VR, which is the receiving-end voltage, and IR, the receiving-end current, and (b) express IS, which is the sending-end current, in terms of VR and IR. (a) VS= _________ (b) IS= ________
The following parameters are based on a preliminary line design: per unitVS=1.0, VR=0.9 per unit, =5000km,Zc=320,=36.8. A three-phase power of 700 MW is to be transmitted to a substation located 315 km from the source of power. (a) Determine a nominal voltage level for the three-phase transmission line, based on the practical line-loadability equation. (b) For the voltage level obtained in part (a), determine the theoretical maximum power that can be transferred by the line.
A three-phase overhead transmission line is designed to deliver 190.5 M VA at 220 kV over a distance of 63 km, such that the total transmission line loss is not to exceed 2.5 of the rated line MVA. Given the resistivity of the conductor material to be 2.84108-m, determine the required conductor diameter and the conductor size in circular mils. Neglect power losses due to insulator leakage currents and corona.
Transmission line conductance is usually neglected in power system studies. True False