The pressure rise, AP, of a liquid flowing steadily through a centrifugal pump depends on pump diameter, D, angular speed of the rotor, @, volume flow rate, Q, and density, p. The table below gives data for the prototype and for a geometrically similar model pump. For conditions corresponding to dynamic similarity between the model and prototype pumps, calculate the missing values in the table. Variable Prototype Model ΔΡ 52.5 kPa 800 kg/m3 183 rad/s 0.0928 m³/min 999 kg/m3 367 rad/s D 150 mm 50 mm

The pressure rise, AP, of a liquid flowing steadily through a centrifugal pump depends on pump diameter, D, angular speed of the rotor, @, volume flow rate, Q, and density, p. The table below gives data for the prototype and for a geometrically similar model pump. For conditions corresponding to dynamic similarity between the model and prototype pumps, calculate the missing values in the table. Variable Prototype Model ΔΡ 52.5 kPa 800 kg/m3 183 rad/s 0.0928 m³/min 999 kg/m3 367 rad/s D 150 mm 50 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem statement : A simple flow-measurement device for streams and channels is a notch, of angle α, cut into the side of a dam, as shown in Fig. P5.69. The volume flow Q depends only on α, the acceleration of gravity g, and the height δ of the upstream water surface above the notch vertex. Tests of a model notch, of angle α = 55°, yield the following flow rate data: δ, cm: 10 20 30 40 Q, m3/h: 8 47 126 263 Part (A) - Find a dimensionless correlation for the data. (b) Use the model data to predict the flow rate of a prototype notch, also of angle α = 55°, when the upstream height δ is 3.2 m.
In supersonic wind tunnel testing, if different gases areused, dynamic similarity requires that the model and prototypehave the same Mach number and the same( a ) Euler number, ( b ) speed of sound, ( c ) stagnation enthalpy,( d ) Froude number, ( e ) specific-heat ratio
A football, meant to be thrown at 60 mi/h in sea-level air( ρ = 1.22 kg/m 3 , μ = 1.78 E-5 N ? s/m 2 ), is to be testedusing a one-quarter scale model in a water tunnel ( ρ =998 kg/m 3 , μ =0.0010 N . s/m 2 ). For dynamic similarity,what is the proper model water velocity?( a ) 7.5 mi/h, ( b ) 15.0 mi/h, ( c ) 15.6 mi/h,( d ) 16.5 mi/h, ( e ) 30 mi/h
A one-tenth-scale model of a supersonic wing tested at 700 m/sin air at 20 ° C and 1 atm shows a pitching moment of 0.25kN ? m. If Reynolds number effects are negligible, what willthe pitching moment of the prototype wing be if it is flying atthe same Mach number at 8-km standard altitude?
A turbine model has the following characteristics: Effective power: 13, 6 kW; Rotor Diameter: 0.38 meters, Flow: 0.34 ms, Energy Jump: 26.5 J / Kg and 3 R.P.S. rotation It is desired to construct a geometrically similar 1.20 meter diameter turbine that provides a power on the 656 kW axis, we ask: to calculate and justify its answers: a) the specific rotation; b) the unit quantities (rotation, flow and power); c) the rotation, flow and power of the model (bi-unit quantities).
The power P generated by a certain windmill design dependson its diameter D , the air density ρ , the wind velocity V , therotation rate Ω , and the number of blades n . ( a ) Write this relationship in dimensionless form. A model windmill, of diameter50 cm, develops 2.7 kW at sea level when V = 40 m/s andwhen rotating at 4800 r/min. ( b ) What power will be developedby a geometrically and dynamically similar prototype, ofdiameter 5 m, in winds of 12 m/s at 2000 m standard altitude?( c ) What is the appropriate rotation rate of the prototype?
A small wind turbine is tested in a wind tunnel using the following model parameters: ρ = 1.2 kg/m3 , µ = 1.81x10-5 Ns/m2 , v = 12 m/s, A = 0.03 m2 and Cp is measured as 0.42. Assuming dynamic similarity exists, calculate the power output of a full-size turbine of diameter 60 m operating in air of density 1.3 kg/m3 and viscosity µ = 1.73x10-5 Ns/m2 with wind speeds of 15 m/s
Volumetric flow rate, Q, of a pump is a function of impeller diameter d, fluid velocity V, pressure difference DP, fluid density r and viscosity m. a)Determine dimensionless P groups. b)A test is to be performed for a large pump that delivers 1.5 m3 /s of water from 40 cm diameter impeller with pressure rise of 400 kPa. For the test, a model with an 8 cm diameter impeller is to be used. What flow rate should be used and what would be the pressure rise in model pump. Note: The model fluid is water at same temperature as the water in the prototype.
SAE 30 oil at 60 F is pumped through a 6-ft diameter pipeline at a rate of 6650 gal/min. A model of this pipeline is to be designed using a 3-in diameter pipe and water at 60 F as the working fluid. To maintain Reynolds number similarity between these two systems, what fluid velocity will be required in the model? Answer: 0.0338 ft/s. Please show work.
The Keystone Pipeline opener photo hasD = 36 in. and an oil flow rate Q = 590,000 barrels per day(1 barrel = 42 U.S. gallons). Its pressure drop per unitlength, ∆p/L , depends on the fluid density ρ , viscosity μ ,diameter D , and flow rate Q . A water-fl ow model test, at20 ° C, uses a 5-cm-diameter pipe and yields ∆ p/L ≈ 4000Pa/m. For dynamic similarity, estimate ∆ p/L of the pipeline.For the oil take ρ = 860 kg/m 3 and μ = 0.005 kg/m . s.
A one-fiftieth-scale model of a military airplane is tested at1020 m/s in a wind tunnel at sea-level conditions. Themodel wing area is 180 cm 2 . The angle of attack is 3 ° . If themeasured model lift is 860 N, what is the prototype lift,using Mach number scaling, when it flies at 10,000 m standardaltitude under dynamically similar conditions? Note:Be careful with the area scaling.
A 1:7 scale model simulates the operation of alarge turbine that is to generate 200 kW with a flowrate of 1.5 m3/s.What flow rate should be used inthe model, and what power output is expected?(a) Water at the same temperature is used in bothmodel and prototype.(b) The model water is at 25°C and the prototypewater is at 10°C.