Kindly solve this using Primary Dimensions. Thank you very much The rate of heat transfer through a composite pipe is given by the equation:Cold fluid (air)tof(AHotfluid :tht2tL(tnf – tef)QIn (r2/r¡) , In (r3/r2)+1+1[hnf•r1KAkBhef.73]convective heat transfer coefficient and k is the thermal conductivity. Write the equationin primary dimensions and show that it is homogenous.Where the subscript hf refers to the hot fluid and cf refers to the cold fluid. h is theB.

Primary dimensions are those dimensions which are not derived from any mathematical quantity i.e.…

The rate of heat transfer through a composite pipe is given by the equation: Cold fluid (air) hot B (A) Hot fluid i 2tL(tnf – tef) Q = 1 + In (r2/ri) , In (r3/r2) . 1 + + ka kg hef.3] Where the subscript hf refers to the hot fluid and cf refers to the cold fluid. h is the convective heat transfer coefficient and k is the thermal conductivity. Write the equation in primary dimensions and show that it is homogenous.

The rate of heat transfer through a composite pipe is given by the equation: Cold fluid (air) hot B (A) Hot fluid i 2tL(tnf – tef) Q = 1 + In (r2/ri) , In (r3/r2) . 1 + + ka kg hef.3] Where the subscript hf refers to the hot fluid and cf refers to the cold fluid. h is the convective heat transfer coefficient and k is the thermal conductivity. Write the equation in primary dimensions and show that it is homogenous.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.35P

See similar textbooks

Similar questions

Liquid biofuel (density= 789 kg/m3) is being pumped from a storage tank through a pipe with 1-inch innerdiameter (ID). The fuel is being pumped at a rate of 3.00 gallons per minute. In this process, what is thekinetic energy transport rate (Ėk) in units of horsepower (hp) and ft•lbf/sec.
Completely solve and box the final answer. Write legibly 2. Calculate the convective heat transfer in KW from air to the circular tube 7.7 meter long with an inside diameter of 127.7 mm. Tube’s temperature along the entire length is 27.7ºC. The average temperature of hot air flowing through the tube is 127.7ºC. Convective film coefficient is 27.7 W/m2-ºK.
An important parameter in fluid flow problemsinvolving thin films is the Weber number (We) which canbe expressed in equation form.where p is the density of the fluid, v is a velocity, L is alength, and O" is the surface tension of the fluid. If the Webernumber is dimensionless, what are the dimensions of thesurface tension O"?
An important parameter in fluid flow problems involving thin films is the Weber number (We) which can be expressed in equation form as We=[pv^2L/(omega)] where p is the density of the fluid, v is a velocity, L is a length, and (omega) is the surface tension of the fluid. If the Weber number is dimensionless, what are the dimensions of the surface tension (omega)?
Cold water enters a pipe, where it is heated by an external heat source . The inlet and outlet water temperatures are Tin and Tout, respectively. The total rate of heat transfer Q. from the surroundings into the water in the pipe is Q. = m·cp(Tout − Tin) where m . is the mass flow rate of water through the pipe, and cp is the specific heat of the water. Write the primary dimensions of each additive term in the equation, and verify that the equation is dimensionally homogeneous. Show all your work.
Henri Darcy, a French engineer, proposed that the pressuredrop ∆ p for fl ow at velocity V through a tube of length Lcould be correlated in the form ∆p ___________ = α LV2 ρ If Darcy’s formulation is consistent, what are the dimensionsof the coefficient α ?
You are working in a machine tool manufacturing industry for the project to design CNCcontrol shaper machines. In the shaper machine, a rectangular plate of 8.75 m2area hasto move slowly at a constant speed of 20 mm/minute over a fixed plate. The distancebetween the moving and fixed table is 0.0254 mm, and the gap is filled by a fluid ofviscosity 8.17 × 10−5 N−sm2. Calculate the amount of force required to move the plate.
Write the primary dimensions of each of the following variables from the field of thermodynamics, showing all your work: (a) energy E; (b) specific energy e = E/m; (c) power W . .
Write the primary dimensions of the universal ideal gas constant Ru. (Hint: Use the ideal gas law, PV = nRuT where P is pressure, V is volume, T is absolute temperature, and n is the number of moles of the gas.)
For the flow geometry from the top of a flat plate, the velocity profile around the plate is given as v (y) = ay+by^2-cy^3, and the temperature profile as T (y) = d+ey+fy^2-gy^3. Derive the mathematical expressions that give the regression coefficient and the heat transfer coefficient. CREATE THE KNOWN AND UNKNOWN BY DRAWING THE SHAPE OF THE ORGANIZATION AND WRITE ALL THE ASSUMPTIONS IN DETAIL
Two endlessly long flat plates, separated by 3 inches in distance but with a thickness of 5 inches, each transport alcohol (5 m/s, 1 Pa·s, S.G. 0.89 (ref. water at 4 degrees Celsius) to a given location with a specific velocity. Prove that the Reynold's number of the following problem is a value approximately around 90-100.
Using dimensional analysis obtain an expression for nusselt number in terms of Reynolds number and prandtl number