"State clearly your assumptions""FOUR Decimal places" 5. Determine the Reynoldsnumber and type of flowoccurring when carbontetrachloride at 22 C flows at avelocity of 1.25 m/s in an 100-mm diameter pipe. *834,852 / turbulent flowO 234,852 / turbulent region324,587 / turbulent regionO 2,219 / laminar flowO 209,220 / turbulent flow 6. Determine the shear stressat the walls of a 12" diameterpipe when water flowingcauses a measured lost headof 15 ft in 300 ft of pipelength.*

Answered: Image /qna-images/answer/1853c331-a43a-4597-9d6a-8147036e0d2c.jpg

5. Determine the Reynolds number and type of flow occurring when carbon tetrachloride at 22 C flows at velocity of 1.25 m/s in an 100 mm diameter pipe. * 834,852 / turbulent flow 234,852 / turbulent region 324,587 / turbulent region O 2,219 / laminar flow 209,220 / turbulent flow

5. Determine the Reynolds number and type of flow occurring when carbon tetrachloride at 22 C flows at velocity of 1.25 m/s in an 100 mm diameter pipe. * 834,852 / turbulent flow 234,852 / turbulent region 324,587 / turbulent region O 2,219 / laminar flow 209,220 / turbulent flow

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gas (ρ = 0.07088lbm/ft3, μ = 0.04615 lbm/ft-hr) is to be transported through a 550 ft long circular cast iron pipe at a rate of 14ft3/s. If the head loss must not exceed 60ft, determine the velocity of flow, Reynolds Number and Darcy-Weisbach Friction Factor, mass flowrate and minimum required diameter of the pipe
Water at 10°C flows in a 1.2-cm-diameter pipe at a rate of 1.33 L/min. The hydrodynamic entry length is (a) 0.60 m (b) 0.94 m (c) 1.08 m (d) 1.20 m (e) 1.33 m
Water at 27.5°C flows at a rate of 2.1 kg/s through a vertical pipe with an internal diameter of 17 mm, where a Pitot tube (with a differential manometer containing mercury at ρHg = 13600 kg/m3) is attached. . When the Pitot tube is positioned at a certain distance from the wall, the manometer reading indicates Δh = 12 cm. What is the velocity of the fluid at this point?
Engine oil at 40°C (? =876kg/m3, ?=0.2177kg/m⋅s) flows in a 20-cm-diameter pipe at a velocity of 0.9 m/s. The pressure drop of oil for a pipe length of 20 m is (a) 3135 Pa (b) 4180 Pa (c) 5207 Pa (d) 6413 Pa (e) 7620 Pa
A venturi meter equipped with differential pressure gage is used to measure the flow rate of water with a mass density of 999.1 kg/m^3 through a 5 cm diameter horizontal pipe. The diameter of the venturi neck is 3 cm and the measured pressure drop is 5 kPa. Taking the discharge coefficient to be 0.98, determine the average velocity through the pipe in m/s. Include a diagram in your solution. a.3.2 b.4.2 c.2.2 d.1.2
A fan draws 1.42 m3 per second of air at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency if total fan mechanical is 70% and air is measured at 25 0C and 760 mmHg. Using p water formulaPw=
Certain oil with sp.gr 0.96 is pumped through a large pipe of diameter 500mm. Velocity of the oil at inlet is 0.2m/s. The outlet of the pipe is at an elevation of 50m above the inlet. The pressure of the oil at the inlet is 50N/cm2. For these conditions determine the volume flow rate and the mass flow rate of oil through the pipe. Determine the total head at the inlet of the pipe and at the outlet of the pipe.
Water at 10°C (ρ = 999.7 kg/m3 and μ = 1.307 × 10−3 kg/m·s) is flowing steadily in a 5 -cm- diameter, 20-m-long circular stainless steel pipe. Determine(a) for a pressure drop of 10 KPa, what would the volumetric flow rate be?
As a test to determine the effective wall roughness of an existing pipe installation, water at 10°C is pumped through it at the rate of 300 L/min. The pipe is standard steel tubing, 40 mm OD x 3.0 mm wall. Pressure gages located at 25 m apart in a horizontal nm of the pipe read 1235 kPa and 849 kPa. Determine the effective pipe wall roughness.
In the continuous and uncompressed flow of water with a temperature of 20ºC and density of 998 kg/m3, the flow rate in the pipe with a diameter of 50 cm was measured as 250 lt/s with an orifice plate with a hole diameter of 30 cm and a discharge coefficient of C=0.61. What is the pressure difference shown by the orifice as kPa? a. 1.032 b. 1.112 c. 1.486 d. 1.601 e. 1.410
A venturi meter equipped with differential pressure gage is used to measure the flow rate of water with a mass density of 999.1 kg/m^3 through a 5 cm diameter horizontal pipe. The diameter of the venturi neck is 3 cm and the measured pressure drop is 5 kPa. Taking the discharge coefficient to be 0.98, determine the flow rate of water in L/s. Include a diagram in your solution. a.3.35 b.1.35 c.4.35 d.2.35
Water with a temperature of 20 oC is pumped from a tank open to the atmosphere (zA = 2.62 m), through two cast iron (roughness value ε=0.005mm) pipes of 26.2 m length, connected in parallel with the higher one (zB = 9.62 m). Pipe diameters are D1 = 3.62 cm and D2 = 5.62 cm, respectively. The water is pumped with a motor-pump group, whose efficiency is 66.2% and consumes 7062 W of electrical power during operation. miner losses in pipes connecting parallel pipes to tanks are neglected. Find the total volume flow rate between the tanks and the volume flow rate in each of the parallel pipes. Solve the problem by making at least three iterations. Solve the problem by making the necessary assumptions and drawing the schematic figure. (a=6 and b=2 on the figure)