Answered: The rated single phase supply in Oman…

Engineering

Electrical Engineering

The rated single phase supply in Oman is Select one: O 230 V, 60 Hz O 440 V, 60 Hz O 440 V, 50 Hz O 230 V, 50 Hz

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.23MCQ: In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the...

See similar textbooks

Related questions

Q: A three phase star-connected load is drawing power at a voltage of 0.9 pu and 0.8 power factor…

A: Given: Base voltage Vb=0.9 pu Power factor cosϕ=0.8 lagging Base KVA=100 MVA=100×103 kVA Base…

Q: 2. A three-phase alternator has a rating of 5000 kVA at 13.2 kV. Calculate the full-load line…

A: Given: S=5000 KvA V=13.2 KV we know that S=3×V×I I= Load Current

Q: A three phase load is connected to three phase supply of 173.205) 50 Hz. The phase impedances of Y…

A: 3 phase unbalanced load supplied by 173.20V voltage source. Assume load is star type, load Y and B…

Q: The most common system for secondary distribution is . . 3-phase, wire system 33kV/11kV, 4 O…

A: Secondary distribution is a part of an electric power distribution network. It carries electric…

Q: An alternator with a line voltage of 2400 V supplies a delta connected load. The line current…

Q: In a delta connected system, the three phase currents are mutually displaced by 120 degree. Select…

A: In the question, Consider the delta connected system, Are the three phase currents mutually…

Q: Two wattmeters are connected to a 3 phase, 3 wire positive sequence system with a 100 V output…

A: To measure the power in a three-phase, three-wire star or delta linked to the balanced or unbalanced…

Q: Given a star connected system with power factor of 80 percent, true power of 2,500 kW and phase…

Q: 1. Assume that a 2.5-kV 1-phase circuit feeds a load of 450 kW at a lagging load power factor and…

Q: A single phase transmission line is delivering 450 kVA load at 13 kV. Its resistance is 6.5 e and…

A: Disclaimer: Since you have asked multipart questions, we will solve the first three subpart for…

Q: step up chopper operating with a frequency of 10kHz. The source voltage is 50V and load voltage is…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: Problem #16: A substation operating at full load of 1200 kVA supplies a load at 0.7 power factor…

Q: A Y-Y three-phase system has a source of 380 V and a load of impedance of 6+j5 Ohm/phase through a…

A: Given the line voltage of the three-phase system.

Q: A single phase transmission line is delivering 500 kVA load at 2 kV. Its resistance is 0-2 2 and…

A: The solution can be achieved as follows.

Q: three-phase load has a line voltage of 480V and a line current of 10A. What is the three phase…

Q: , each transmission line of the three-phase system has an impedance of 0.2/90° Q. In the

A: NOTE- “Since you have posted a question with multiple sub-parts, we will solve first three subparts…

Q: . A balanced delta connected load whose impedance is 45470° ohm per phase, a three phase motor that…

A: Notes Line voltage and phase voltage in delta connected system remain same. Line current and phase…

Q: 2. A three phase Y connected balanced resistive load is connected to a three phase Y connected…

A: Dear student we have limited time to solve your question.we will answering first question for…

Q: The line input to a three-phase star connected alternator having a line input of 400V 50Hz supplies…

Q: In a star 3 phase connection circuit, the phase current is equal to its line current. Select one: O…

A: Star Connection: This system is also known as Three Phase Four Wire System (3-Phase 4 Wire). This…

Q: (A V E, V

A: The solution is given below

Q: Convert the delta connected impedances of 12∠360 deg ohms to balanced wye connected impedances.

Q: Q. 3a) Each phase of delta connected load comprises a resistor of 50 ohm and a series capacitor of…

Q: e) Calculate the phase current IAB. f) Calculate the total average power dissipated in the…

A: In the power system Find the phase current Total dissipate power across the load Ratio of the power…

Q: A three phase distribution board of installed power 50KVA is supplied at 220/380V with a demand…

Q: A Y-Y three-phase system has a source of 380 V and a load of impedance of 6+j5 Ohm/phase through a…

A: The given connection is a three-phase Y-Y balanced connection. The phase voltage for the star…

Q: A single phase transmission line is delivering 500 kVA load at 2 kV. Its resistance is 0·2 Ω and…

A: Given a single phase transmission line with Load : 500 KVA at 2 KV Resistance=0.2Ω inductive…

Q: The load to the three phase supply comprises three similar coils connected in Star. The line current…

A: From given kva and kw calculate phase and line voltage and KVAR. Power factor =active power/apparent…

Q: A four wire 208 V three-phase system is used to supply power to a three-phase 5-hp induction motor…

Q: A balanced three-phase star-connected load of 150 kW takes aleading current of 100 A with a line…

A: Balance 3 phase star connected load Power P= 150KW leading current 100A Line voltage 1100V Then…

Q: In three phase star connected system, the phase voltage is equal to line voltage. Select one: True…

A: In three phase star connected system, the phase voltage Vph= ( line voltage)VL)/√3 But the phase…

Q: In single phase overhead transmission lines, the increase of the line impedance leads to an increase…

A: Single phase overhead transmission lines, the increase of the impedance leads to an increase of ...…

Q: In a star connected system if the line voltage is 240V, then the phase voltage will be. 240 V 138.56…

A: Give a star connected system with, Line voltage, VL=240 V

Q: A balanced 3 - phase load consists of three coils. each of resistance 6 W. and inductive reactance…

Q: balanced positive sequence Y-connected source with the phase voltage Van = 10010° V is connected to…

A: 1. Since it is a balanced load the value of all of the impedance in the delta circuit will be equal.…

Q: In the power measurement of three phase delta connected load, the terminals 'M' and 'C' of the…

A: Wattmeter is used to measrure power. It has two coils namely, current coil and pressure coil.

Q: Answer the question in the below Image. A single phase transmission line is delivering 500 kVA load…

Q: In three phase delta connected system, the phase voltage is equal to line voltage Select one: True…

Q: A three phase balanced load is connected across 220 V three phase source. A wattmeter reads 600…

A: Given: W1=600 WW2=600 W Calculate the load angle; tanφ=3W1-W2W1+W2tanφ=3600-600600+600tanφ=0…

Q: Develop the admittance matrix Ybus

Q: 20. If you stub a motor winding, you A. reinforce the insulation. B. form phase-pole groups.

A: Insulation in slots is no need to change or reinforce. If motor winding is stubbed then it should…

Q: In a three-phase loading system non identical load impedances refers to Select one: O a. Ideal load…

A: Un balanced load means that the magnitude of impedance per phase is not same.

Q: Three identical coils are connected as delta load to a three phase supply. The line current drawn…

Q: A three phase motor have totally six terminals for connection. Select one: True False

A: As per the guidelines of Bartleby we supposed to answer first question only for remaining questions…

Q: One phase voltage of a balanced Y-connected source is V, = 1802 – 20° V. If the source is connected…

Q: Example 42: A single phase 208V AC control power to R=42 load if the desired output power is 3 KW,…

A: Given, Supply voltage, V = 208 V Load resistance, RL = 4 ohm Output power, Po = 3 kW

Q: balanced delta connected source is supplying a delta connected load such that it draws 2000 kW at…

A: First we will find out the current and voltage is given so impedance is the ratio of voltage to…

Q: a single line transmission line having 500 kva load at 2kv it resistance is 0.2 ohm and inductive…

A: Given data, A single transmission line having S=500 kVAVR=2 kVR=0.2 ΩXL=0.2 ΩPf cosϕR=0.707 leading…

Q: -F{V;®[v,Y# + EYijV,"}} j#i j=1 j#i Write a method in details to determine Q and phase angle of V at…

A: A power network is an interconnection large and complex network and analyzed by different plow flow…

Q: Problems > A three phase has 600 primary turns and 150 secondary turns. If the supply voltage is 1.5…

Question

The rated single phase supply in Oman is
Select one:
O 230 V, 60 Hz
O 440 V, 60 Hz
O 440 V, 50 Hz
O 230 V, 50 Hz

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Concept of Single Phase Supply

VIEW

Step 2: Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the line-to-neutral voltages are always equal to zero. (a) False (b) True
20. If you stub a motor winding, youA. reinforce the insulation.B. form phase-pole groups.
Consider a 3-phase delta-star configuration with a generator and a 3-phase load. The generator supplies voltage of grid-standard 380/220V@50Hz. Each load is (15+15j) Ω.
A 100 km long three phase transmission line has resistance 12Ω per phase, inductance per phase 0.15 Hanni, capacitance between each phase and neutral 0.8uF. At the far end a load of 30 MW at 110 kV, 50 Hz frequency is connected at 0.8 power factor. So ( 1 ) sending end voltage ( 2 ) sending end current
Circuit Impedance Z = (ohms) Phase Angle = arc cos R/Z = Calculated Is = (A) Calculate Ic = (A) Calculate Ir= (A) Calculate Il= (A)
Transient stability of the power system can be improved by using.O Parallel LinesSingle LinesO Single Bundled LinesO Alloy conductors
Circuit Impedance Z= (ohms) Phase Angle = arc cos R/Z = Calculate Es= (V) Calculate Ec= (V) Calculate Er= (V) Calculated El= (V)
A three-phase Y-connected synchronous generator is rated 100 MVA, 12.5 kV, 0.85 PF leadingand 50 Hz. Its synchronous reactance is 1.0 0, and its resistance may be ignored. Analyze thevoltage regulation of this generator
. In a 50 Hz short transmission line, receiving end phase voltage is 172.1 V and receiving end phase current is 0.5521 A. The line has resistance of 18 Ω and inductance of 300 mH. Calculate the sending end phase voltage.
Circuit Impedance Z = (Ω) Phase Angle =arc cos R/Z= Calculate Es = (V) Calculate Ec=(V) Calculate Er =(V)
A single phase transmission line is delivering 500 kVA load at 2 kV. Its resistance is 0·2 Ω and inductivereactance is 0·4 Ω. Determine the voltage regulation if the load power factor is (i) 0·707 lagging (ii)0·707 leading.
Electrical machine Determine the per phase nominal impedance of a 30 MVA, 15kV three-phase alternator