A three phase star-connected load is drawing power at a voltage of 0.9 pu and 0.8 power factor lagging. The three phase base power and base current are 100 MVA and 437.38.A respectively. The line-to-line load voltage in kV is

A three phase star-connected load is drawing power at a voltage of 0.9 pu and 0.8 power factor lagging. The three phase base power and base current are 100 MVA and 437.38.A respectively. The line-to-line load voltage in kV is

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.19P: Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current...

See similar textbooks

Related questions

Q: 0.038 +/0.072 f/phase. Calculate the line-to-line source volt- age magnitude required so that the…

A: For Star connection, Line voltage, VL = 3 * Phase voltage, VPh Line current, IL = Phase current,…

Q: The sending-end and receiving-end voltages of a three-phase transmission line at a 200 MW load are…

A: According to the question we have to find the value of the maximum steady-state power that can be…

Q: In a three phase overhead system , each line is suspended by a string of three insulator. The…

Q: A single phase transmission line is delivering 500 kVA load at 2 kV. Its resistance is 0-2 0 and…

Q: Two wattmeter's are connected to measur the input power of a balanced three phase load by two…

A: Watt-merter reading W1 = 8800w W2 = 3500 W

Q: Note: It is expected from student to develop impedance matrices of three phase power system. Develop…

A: From the given power system network Impedance matrix is develop as shown below

Q: A short line having an impedance of (2 + j3) ohm interconnects two power stations A and B both…

A: Without booster, We can draw the power plant as PR=25MWQR=PRtancos-10.8QR=25tancos-10.8…

Q: 0.038 +0.072 f/phase. Calculate the line-to-line source volt- age magnitude required so that the…

A: In star connection, Line voltage, VL = 3 * Phase voltage, VPh Line current, IL = Phase current, IPh…

Q: A 3-phase 11kv generator feeds power to upf load of 100mw through 3-phase transmission line. The…

Q: The resistance and reactance of the single- phase 60HZ transmission line conductors are 7.2 ohm and…

Q: In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the…

A: In three phase balanced system each phase is displaced by 120 degrees each other. In case of…

Q: For a single phase network shown in the figure below, work in per-unit with 200 VA & 250 V as base…

A: In this question we need to find a load current of the given system.

Q: Two wattmeter’s are connected to measure the input power of a balanced three phase load by two…

A: For this problem we can easily found power factor. As wattmeter is connected with reverse switch we…

Q: The RL (Resistive and Inductive) Load in the Load Side Section of the Distribution Line Simulator is…

A: This question is based on the load connection in the distribution line simulator. RL load in the…

Q: A load of 135 MW at a power factor of 0.65 lagging can be delivered by a 3-phase transmission line.…

Q: Answer the question in the below image. A single phase transmission line is delivering 500 kVA load…

Q: An overhead 3-phase transmission line delivers 5000 kW at 22 kV at 36.86" lagging. The resistance…

Q: A load of 125 MW at a power factor of 0.6 lagging can be delivered by a 3-phase transmission line.…

A: single phase power=3 phase power 3. per phase voltage=Line voltage3. line current=power…

Q: Example 60 MVA, 13.8 kV a balance three phase load with 0.8 lagging power factor. Determine for the…

Q: A single phase transmission line is delivering 450 kVA load at 12 kV. Its resistance is 4.5 and…

A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: . Calculate the line currents for phase a, b and c. 2. Calculate the line-to-neutral voltages at the…

A: From the given circuit Van = 120 ∠0 V V bn = 120∠-120 V V cn = 120 ∠-240 V R a=R b=R c=…

Q: A single phase transmission line is delivering 440 kVA load at 11 kV. Its resistance is 50 and…

A: Sending end voltage =receiving end voltage +drop in the line. Efficiency = output power/input power.…

Q: A single phase transmission line is delivering 440 kVA load at 11 kV. Its resistance is 50 and…

A: As per Bartleby guidelines we are allowed to solve only three subparts, please ask the rest again.

Q: In 3 phase 11kVV generator having unity power factor of 100MW load and the sending and receiving end…

A: The diagram for the sending and receiving end is shown below:

Q: A 12500 kVA load is supplied at a power factor of 0·8 lagging by a 3-phase transmission line whose…

A: Draw the circuit diagram containing load transmission line with the given parameter, To…

Q: Two wattmeter’s are connected to measure the input power of a balanced three phase load by two…

A: As one of wattmeter is connected with reverse switch so it will reading negative power.

Q: Determine the per unit impedance of a transmission line having an impedance of 30 + j110 Ω on 100…

Q: Draw an impedance diagram for the electric power system shown in the figure attached, showing all…

A: We can obtain the impedance diagram by using below steps: -The base voltage VBG1 on the LV side of…

Q: A load of 120 MW at a power factor of 0.8 lagging can be delivered by a 3-phase transmission line.…

A: Solution:- Given, PL-3ϕ =120 MW PL-1ϕ = 40 MW Pf = 0.8 lagging VR-1ϕ = 45 × 1033= 25.9807 KV Single…

Q: A 3-phase balanced load draws a line current of 80Amperes at 240V line to line and a 0.820 lagging…

Q: A single phase transmission line is delivering 430 kVA load at 13 kV. Its resistance is 4.5 Q and…

A: According to question: a) The current through the transmission line is calculated as…

Q: Referring to the circuit shown below, determine the following: (a) The voltage between points e and…

A: Calculation of voltage and power factor of above circuit.

Q: Two Alternators are operating in parallel supplying a common load of 4250KW at 85% power factor…

Q: A load of 140 MW at a power factor of 0.6 lagging can be delivered by a 3-phase transmission line.…

A: Given 3-phase transmission line Load PL=140 MWPower factor PF=0.6 lagReceiving end voltage VR=36…

Q: 5. Assume that a 2.5-kV 1-phase circuit feeds a load of 450 kW at a lagging load power factor and…

A: consider the given question;

Q: The scheduled power at the bus of a power system is the Difference of the Generation and load power…

A: A bus in a power system is defined as the vertical line at which the several components of the power…

Q: A power station has to meet the following load demand: LOAD A 50kW Between 10 AM and 6 PM LOAD B…

A: The solution can be achieved as follows.

Q: Assume that a 2.5-kV 1-phase circuit feeds a load of 450 kW at a lagging load power factor load…

A: IL=215 a, PL=450Kw VL=2.5 kv(i) load apparent power sL=VLIL =2.5K×215 =537.5…

Q: ) Calculate the phase voltages of the following zero, positive, and negative sequences of phase "a"…

Q: A short 3-φ transmission line with an impedance of (5 + j 20) Ω per phase has sending end and…

A: Resistance of each conductor R=5 ohm Reactance of each conductor XL=20ohm Load power factor is 0.8…

Q: The sensitivity of a node to real power changes is 100 MW/kV of line voltage and that to reactive…

Q: A set of balanced three-phase transmission lines with line-to-line voltages of 13 kV is connected to…

A: Given: For balanced 3-phase star-connected load, per-phase impedance Z=8+3j Ω=8.544∠20.55° Ω,…

Q: A three-phase 440-V, 50-kW, 60-kVA inductive load operates at 60 Hz and is wye-connected. It is…

A: Active power to motor before and after the power factor correction is ramains same. Capacitor can…

Q: Two wattmeter's are connected to measure the input power of a balanced three phase load by two…

A: i have explained in detail

Q: A load of 120 MW at a power factor of 0.6 lagging can be delivered by a 3-phase transmission line.…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: A short single phase transmission line has a loop impedance of (0.2+j1.2) ohm. At what leading power…

A: Given: A short single phase transmission line has, Loop impedance, Z=0.2+j1.2 Ω so Resistance, R =…

Q: In a three-phase balanced star connected system, the phase relation between the line voltages and…

A: We will draw phasor diagram of the star connected system showing phase voltages and line voltages.…

Q: A load of 145 MW at a power factor of 0.8 lagging can be delivered by a 3-phase transmission line.…

Q: The three phase power and line-line ratings of the below electric power system is given below: T Vm…

A: The given system is, For generator: For motor: And

Question

A three phase star-connected load is drawing power at a
voltage of 0.9 pu and 0.8 power factor lagging. The three phase
base power and base current are 100 MVA and 437.38.A
respectively. The line-to-line load voltage in kV is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Single Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
A single-phase source is applied to a two-terminal, passive circuit with equivalent impedance Z=3.045, measured from the terminals. The source current is i(t)=22cos(t)kA. Determine the (a) instantaneous power, (b) real power, (c) reactive power delivered by the source, and (d) source power factor.
A single phase, unity power factor load takes 90 Amps at 10 kV. Using a base voltage of 65 kV and base kilovolt amperes of 4475 kVA. Find the base current, base impedance, base power, per unit current and per unit voltage of the load.
Using a test equipment, Vmax was found to be 5V while Vmin is 1V. The distance between voltage maximas is 14 cm and the first maximum was found to be 7 cm from the load. What is the load impedance if the characteristic impedance of the line is 75 ohms?
The impedance per phase of 3-phase transmission line on a base of 100 MVA, 100 kV is 2 pu. Find the value of this impedance on a base of 400 MVA and 400 kV would be..
The sending-end and receiving-end voltages of a three-phase transmission line at a 200 MW load areequal at 230 kV. The per phase line impedance is j14 ohm. The maximum steady-state power that canbe transmitted over the line is
Give a full math analysis for the 3-phase circuit shown in the figure.
The annual load duration curve of a power supply system may be considered as straight line from 40 MW to 8 MW. The load factor of the system is ?
A short single phase transmission line has a loop impedance of (0.2+j1.2) ohm. At what leading power factor the voltage regulation will be zero ?
a short three phase transmission line connected to 33kv 50 hertz generating station at starting and is required to supply a load of 10 MW at pointed start lagging power factor at 30 KV addresses in that is the minimum transmission efficiency is to be determined96% estimate the per face value of resistance and inductance of a line
Write a report on the Star connection for three phase load experiment using the data/results from the experiment.