The recipe for PBS says to dissolve compounds in 800 ml of water, adjust the pH to 7.4, then add water up to 1 litre. The final pH should still be 7.4, because the pH of buffer solutions remains stable when they are diluted as long as the concentration of its constitutive acid and base is not too low. Why do you think the protocol does not say to dissolve compounds directly in 1 litre of water?

The recipe for PBS says to dissolve compounds in 800 ml of water, adjust the pH to 7.4, then add water up to 1 litre. The final pH should still be 7.4, because the pH of buffer solutions remains stable when they are diluted as long as the concentration of its constitutive acid and base is not too low. Why do you think the protocol does not say to dissolve compounds directly in 1 litre of water?

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter4: Stoichiometry: Quantitative Information About Chemical Reactions

Section4.9: Spectrophotometry

Problem 3.1ACP

See similar textbooks

Similar questions

Your goal is to make a buffer with a pH of 4.75 from acetic acid and sodium acetate. Assume the pKa for acetic acid is 4.74. What is the volume of 1 M sodium acetate added to make your buffer? Report your answer to the tenths place. To do this, we use the Henderson-Hasselbach Equation pH = pkA + log (base/acid) where pkA = 4.74 for acetic acid, pH = target pH and [base] /[acid] = x/(1-x) since we don't know the concentration of the base, we will call it x the acid is just 1-x, assuming the two add up to 100% solve for x, and then you know the mL of base and acid to add.
Your goal is to make a buffer with a pH of 4.95 from acetic acid and sodium acetate. Assume the pKa for acetic acid is 4.74. What is the volume of acetic acid added to make your buffer? Report your answer to the tenths place. To do this, we use the Henderson-Hasselbach Equation pH = pkA + log (base/acid) where pkA = 4.74 for acetic acid, pH = target pH and [base] /[acid] = x/(1-x) since we don't know the concentration of the base, we will call it x the acid is just 1-x, assuming the two add up to 100% solve for x, and then you know the mL of base and acid to add.
please stop rejecting. we pay for this service, so we deserve getting our answer! I do not want to have to put a claim in and report Use acid-base titration to determine theconcentration of:– A strong acid: HCl 0.100 M NaOH (standardized)•0.100 M HCl0.100 M CH3COOH Phenolphthalein is used for endpoint determination– Changes from colourless to pink as a solution becomes more basic• Only need 2-3 drops per titration• pH range: 8.3-10
A 0.4071-g sample of pure CaCO3 was transferred to a 500-mL volumetric flask, dissolved using a minimum of 6 M HCl, and diluted to volume. After transferring a 50.00-mL portion of this solution to a 250-mL Erlenmeyer flask, the pH was adjusted by adding 5 mL of a pH 10 buffer. After adding an indicator, the solution was titrated with the EDTA, requiring 42.63 mL to reach the end point. What is the concentration of EDTA? Choices: 0.0191 M, 0.0955 M, 0.00955 M, 0.477 M
One day it was discovered that the waters of the lake were dead, estimated to be polluted Hg. How do you analyze whether it is true that the cause of death of this fish is due to the presence of mercury? What you would do as an analytic see this incident. Some standard solutions with concentrations of 2 ppm, 4 ppm, 6 ppm, 8 ppm and 10 ppm have absorbants of 0.1 each; 0,3 ; 0,5 ; 0,7 ; 0.9. Determine what the concentration of the sample if analyzed has absorbants of 0.32 and and 0.025. Explain how you analyzed it. A student wants to do a laboratory practicum by bringing students. In practicum you need sulfuric acid with a concentration of 0.1 N. While in laboratory there is sulfuric acid pa with a density of 1.84 gr / ml and 96 % w / w. Explain how you took the steps so that a 0.1 N sulfuric acid solution is available during practicum
If to 100 ml of a solution of CH3COOH with a concentration of 0.0928 N. a) 200 ml of distilled water was added. Determine its new concentration expressed to 4 decimal places, and determine the pH of the final solution. Data: pKa = 4.756 at 25°C. Consider that degree of dissociation is very small. b) If it is mixed with 100 ml of a 0.0989 N CH3COONa solution. What is the pH of the buffer solution.
In a Complexometric Titration Experiment, the preparation of the EDTA solution is as follows: In a 250 mL beaker, weigh 0.10 g MgCl2*6H2O and 1.0 g NaOH. Add approximately 200 mL distilled water and stir to dissolve. Add about 2.0 g of EDTA and transfer the solution quantitatively to a 1-L volumetric flask. Dilute to the mark with distilled water. What is the purpose of adding MgCl2*6H2O? Please show COMPLETE solution.
please explain the process and answer Mouthwash acts to clean and disinfect mouths. Two important considerations when designing a mouthwash solution are the pH, which should ideally not be too acidic (where saliva has a normal pH range of 6.2–7.6 and below pH 5.5 erosion may occur), and the resistance of the solution to changes in pH. One example of a buffering system used in mouthwash is based on the compound H3PO4 which has PKa values of 2.1, 7.2 and 12.3. i. Hand-draw the structure of the main phosphorus species at pH 7.0, as well as a balanced equilibrium equation showing the structures of the two main phosphoric acid species at pH 7.0.
Students Mola and Rity were tasked to analyze the acidity of a 10.0-mL fermented milk sample diluted with water in a 250-mL volumetric flask. Mola obtained a 15.0-mL aliquot of this solution, diluted it to 50.0 mL, and then titrated this diluted sample. Titration data were given to Rity and she found out that the 50.0-mL diluted sample contains 0.21 mmol of lactic acid. MW: Lactic Acid (90.08) a. What is the lactic acid concentration (in M) of the titrated sample? b. Determine the lactic acid content (in M) of the 10.0-mL fermented milk sample. c. What is the lactic acid concentration (in %w/v) of the 10.0-mL fermented milk sample?
Please explain the problem step by step. Thank You! Find the pH of a 1.00 L aqueous solution containing 12.43 g of tris (FM 121.14) plus 4.67 g of tris hydrochloride ( FM 157.60) ? What would be the new pH after adding 12.0 mL of 1.00 M NaOH to this buffer?
Mola and Rity were tasked to analyze the acidity of a 10.0-mL fermented milk sample diluted with water in a 250-mL volumetric flask. Mola obtained a 15.0-mL aliquot of this solution, diluted it to 50.0 mL, and then titrated this diluted sample. Titration data were given to Rity and she found out that the 50.0-mL diluted sample contains 0.21 mmol of lactic acid. MW: Lactic Acid (90.08) Follow proper significant figure rulesa. What is the lactic acid concentration (in M) of the titrated sample? b. Determine the lactic acid content (in M) of the 10.0-mL fermented milk sample. c. What is the lactic acid concentration (in %w/v) of the 10.0-mL fermented milk sample?
Mola and Rity were tasked to analyze the acidity of a 10.0-mL fermented milk sample diluted with water in a 250-mL volumetric flask. Mola obtained a 15.0-mL aliquot of this solution, diluted it to 50.0 mL, and then titrated this diluted sample. Titration data were given to Rity and she found out that the 50.0-mL diluted sample contains 0.21 mmol of lactic acid. What is the lactic acid concentration (in M) of the titrated sample?