The relay mechansm depicted below has the following parameters : Agap0001 square meters, N-500 tuns, L002 meter, the spring constant isk1000 Newtonsimeter, and R18 Ohms. Determine the minimum voltage V that required to make he movable part make contact with the yoke. You may neglect the reluctance of al ron parts and and hriction in the movable part. You may also neglect the resistance of the s00 tum winding e tis assumed to be small compared to R) C Movable pat Swish Spring View Availabie Hintial

The relay mechansm depicted below has the following parameters : Agap0001 square meters, N-500 tuns, L002 meter, the spring constant isk1000 Newtonsimeter, and R18 Ohms. Determine the minimum voltage V that required to make he movable part make contact with the yoke. You may neglect the reluctance of al ron parts and and hriction in the movable part. You may also neglect the resistance of the s00 tum winding e tis assumed to be small compared to R) C Movable pat Swish Spring View Availabie Hintial

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.19P

See similar textbooks

Similar questions

Fill in the data for a 16-ampere electric motor, single-phase, no Code letters. a. Branch-circuit protection, non-time-delay fuses: Normal size _____________AMaximum size _____________A Switch size _____________ASwitch size _____________A b. Branch-circuit protection dual-element, time-delay fuses: Normal size _____________AMaximum size _____________A Switch size _____________ASwitch size _____________A c. Branch-circuit protection instant-trip breaker: Normal setting _____________A Maximum setting _____________A d. Branch-circuit protectioninverse time breaker: Normal rating _____________A Maximum rating _____________A e. Branch-circuit conductor size, Type THHN Ampacity _____________A f. Motor overload protection using dual-element time-delay fuses: Maximum size _____________A
A wind farm is being built on an island 6km offshore and needs to be connected to the power grid substation 12km down shore before it can become operational. The cost of laying cable under water is $10,000/km, and the cost of laying cable on land is $8,000/km. a) Determine the cable route that will minimize cost. b) What is the minimum cost
1) Time-current relay of IDMTL characteristic is generally used to achieve good discrimination in protection of:? (a) Transmission lines (b) Circuit breakers (c) Generators (d) Large motors 2- The time delay coordination (CDT) for overcurrent protection relays. d) None of these. (a) 0.1s (b) 0.2s (c) 0.4s (d) 0.5s 3-power line carrier (PLC) protection scheme is used to protect?A-power transformer, B-large motor c-long transmission lined- short transmission line
a) What applications / experiments are necessary to find the Rc parameter in the equivalent circuit given in Figure 1? b) Write the value of the Ir 'current given in Figure 1 with a sentence in the idle running test of the 3-phase Asynchronous motor.
PROBLEMS i istic such that rated armay, short.circuit characteristic 5 « ; aa'gﬂ?;ciunﬁ e ion. Rated voltaEo on the sitgap line o ts-unit excitation 1s reduted o, su pf lagging? tor is 80% leading. 51, A synchronous gei current is obtained by obtained by 1.25 per-unit excitat = load at rated voltage, rated VA, and 807 52, Repeat Prob, 5-1 for the case where the foad pover fac 5.3, A synchronous generator has the following rating? 180-KVA, 440-V, 300-rpm, 60-Hz, three-Phase: r~0 and x —02960Q Theuit-sap line it described by the equation £ = 1117, RIS = e b Y-connection, expressed per phase. The short. the field current needed
In order for the closed-loop system, whose block diagram is given in the photograph, to be stable, the parameters ?1 and ?2 must be determined.Calculate the values it will take. Draw the graph of the stable region in the ?1-?2 plane. (Hint: Routh-Hurwitzuse the method)
QUESTION 1 The unit step response of a second-order open-loop LTI system is shown below Calculate approximate percentage maximum overshoot? Calculate approximate rise time value? (FYI: The rise time is defined as the time system takes from 10% to 90% of the final value) Calculate approximate settling time value? (FYI: The settling time is defined as the time at which the system reaches to steady-state value and remains within the tolerance of plus or minus 2%)
An example of an invariant feature of a generalized motor program (GMP) is the overall speed involved in performing a skill. Question 23 options: True False
Power system Solve using keypord or dislike Explain why Is increases after shunt compensation with reference to the P. F at the sending end
Apply lasso analysis to find i Commentary: PLEASE, describe the procedure step by step, in detail. Do not do it on paper, digitally here :)
Choose which answers are correct Reliability evaluation deals with the disturbances arising in the power generation system? a . Adequacy based Reliability Evaluation b . Recursive Technique c . Security based Reliability Evaluation d . Reserve margin Method
N K © M =] v : @& docs.google.com/forms/d/¢ 2 Add file Q 1/ B) What is the work of Commutator . * &2, Add file Q 2) The following information is given for a 300-kW, 600-V, long-shunt compound generator : Shunt field resistance = 75 Q, armature resistance including brush resistance = 0.03 Q, commutating field winding resistance = 0.011Q, series field resistance = 0.012 Q, diverter resistance = 0.036 Q. When the machine is delivering full load, calculate the voltage and power generated by the armature * 2 Add file Q 3) A four pole aenerator havina - >