The required clamping force at the board A is to be 1.5 kN (Figure 1). The square-threaded screw has a mean radius of 10 mm and a lead of 3 mm, and the coefficient of static friction is 0.35. Part A Determine the torque M that must be applied to the screw to tighten it down. Express your answer to three significant figures and include the appropriate units. ? M = Value Units Submit Request Answer < Return to Assignment Provide Feedback Figure 1 of 1

The required clamping force at the board A is to be 1.5 kN (Figure 1). The square-threaded screw has a mean radius of 10 mm and a lead of 3 mm, and the coefficient of static friction is 0.35. Part A Determine the torque M that must be applied to the screw to tighten it down. Express your answer to three significant figures and include the appropriate units. ? M = Value Units Submit Request Answer < Return to Assignment Provide Feedback Figure 1 of 1

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.31P

See similar textbooks

Similar questions

Repeat Problem 2.3-18, but assume that the bar is made of copper alloy. Calculate the displacements SBand Scif P = 50 kips, L = 5 ft = 3/5 in., b1= 2.75 in., b2= 3 in., and E = 16,000 ksi.
An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter of an input shaft is d = 20 mm and its material is 16MnCr5. A force of F = 2800 N forces the shaft due to the operation of a gear wheel connected with a wedge on the input shaft. The distances of the gear from the bearings are given as L₁ = 40 mm and L2 = 60 mm. In the most dangerous section, you are required to check the strength according to the S = 3 safety factor. If the section is unsafe in terms of strength, what changes would you make in the design to make it safe? (The surface of the spindle is machined as fine chips, reliability poor Kg = 1.).
A round steel rod made of structural steel, AISI C1118, As rolled is to be used as a column, centrally loaded with 15 kips; N= 2.75. Determine the diameter for (a) L= 20 in. (b) L= 5 in. (c) the same as (a) and (b) except that the material is AISI 9850, OQT 1100 F. Is there any advantage in using this material rather than structural steel?
A cap screw, ¾ in.-10-UNC-2, with a hexagonal head that is 9/16 in. thick, carries a tensile load of 3000 lb. If the material is AISI 1015, cold drawn, find the factor of safety based on ultimate strengths of a. the threaded shank, b. the head against being sheared off, and c. the bearing surface under the head. d. Is there any need to consider the strength of standard cap-screw heads in design?
A cap screw, ¾ in.-10-UNC-2, with a hexagonal head that is 9/16 in. thick, carries a tensile load of 3000 lb. If the material is AISI 1015, cold drawn, find the factor of safety based on ultimate strengths of a.the threaded shank, b.the head against being sheared off, and c.the bearing surface under the head. d.Is there any need to consider the strength of standard cap-screw heads in design?
The shaft in the figure is mounted with a gear wheel key. Shaft material 42CrMo4 The weight of the gear on the shaft is 0.9 kg, dimension, surface and notch factors KbK / Kç = 0.83, shaft speed n = 1120 rpm, shaft transmitted power 7.5 kW, force on shaft Fn = F = 2680 N Since the desired safety coefficient is Ssafe = 2; Check the safety of the shaft
Produced from xCy steel material by machining method, the shaft is bedded at C and D points. With the shaft, constant Fy= 820 N forces in the vertical direction and constant Fx= 4,2 kN forces in the axial direction, which do not rotate together. The tensile strength of the shaft material is (sigma)tensile = (sigma)ut = 620 MPa and the yield strength is (sigma)yield = 420 MPa. For 50% reliability, analyze the fatigue damage condition of the shaft sections A and B separately.
The figure (attached) shows a belt pulley mechanism which is loaded statically. The shaft is made of AISI 1030 steel with the yield strength of 480 MPa. Using distortion energy theory (DET), determine the diameter of the shaft with a factor of safety of 2.
An alloy steel Metric 10x1.5 screw (10 mm diameter, pitch p = 1.5 mm) is to be turned into a threaded hole and tightened to one/half of its proof strength. According to Table 30.2, the proof strength = 830 MPa. Determine the maximum torque that should be used if the torque coefficient = 0.18
(9) A Mercedes Benz gas engine valve spring should not exceed to a cylindrical space of 1¾-in in diameter. The spring index is 6.0 & the maximum load it will have to sustain is l00lb with corresponding deflection of ½-in. The spring is subjected to repeated loading & fatigue must be considered, a low working stress of 40,110psi will be used. Determine: (a) the diameter of wire based on commercial sizes; (b) the number of coils.
A 0.5-in.-diameter steel [E= 30,000 ksi] bolt (1) is placed in a copper tube (2). The copper [E= 16,000 ksi] tube has an outside diameter of 1.00 in., a wall thickness of 0.125 in., and a length of L= 8.0 in. Rigid washers, each with a thickness of t= 0.125 in., cap the ends of the copper tube. The bolt has 20 threads per inch. This means that each time the nut is turned one complete revolution, the nut advances 0.05 in. (i.e., 1/20 in.). The nut is hand-tightened on the bolt until the bolt, nut, washers, and tube are just snug, meaning that all slack has been removed from the assembly but no stress has yet been induced. What stresses are produced in the bolt and in the tube if the nut is tightened an additional quarter turn past the snug-tight condition?
Q) A helical compression spring of a mechanism is subjected to Pas =120 N 19ad cycle. The diameter if the wire is 3 mm, with a spring index of € = 7 P, =4N and .The spring is made of oil-hardened and tempered steel, with”« ~ L0t dm Determine the factor of safety in fatigue loading.