I Review I Constants One end of a uniform meter stick is placed against a vertical wall as shown in (Figure 1) . The other end is held by a lightweight cord that makes an angle 0 with the stick. The Part A coefficient of static friction between the end of the meter stick and the wall is 0.40. What is the maximum value the angle 0 can have if the stick is to remain in equilibrium? Express your answer in degrees. ? = Submit Request Answer Figure 1 of 2 > Part B Let the angle between the cord and the stick is 0 = 16°. A block of the same weight as the meter stick is suspended from the stick, as shown at (Figure 2), at a distance x from the wall. What is the minimum value of x for which the stick will remain in equilibrium? Express your answer in centimeters. ΑΣφ ? cm Submit Request Answer

I Review I Constants One end of a uniform meter stick is placed against a vertical wall as shown in (Figure 1) . The other end is held by a lightweight cord that makes an angle 0 with the stick. The Part A coefficient of static friction between the end of the meter stick and the wall is 0.40. What is the maximum value the angle 0 can have if the stick is to remain in equilibrium? Express your answer in degrees. ? = Submit Request Answer Figure 1 of 2 > Part B Let the angle between the cord and the stick is 0 = 16°. A block of the same weight as the meter stick is suspended from the stick, as shown at (Figure 2), at a distance x from the wall. What is the minimum value of x for which the stick will remain in equilibrium? Express your answer in centimeters. ΑΣφ ? cm Submit Request Answer

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.92RP: The test specimen AB is placed in the grip of a tension-testing machine and secured with a wedge....

See similar textbooks

Similar questions

A 1.1-kg disk A is placed on the inclined surface. The coefficient of static friction between the disk and the surface is 0.35. Is the disk in equilibrium if P=5.5N and =30?
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The test specimen AB is placed in the grip of a tension-testing machine and secured with a wedge. The coefficient of static friction at both surfaces of the specimen is s. If the wedge angle is =18, determine the smallest s for which the grip is self-locking (no slipping takes place regardless of the magnitude of the force P). Neglect the weight of the wedge.
Find the largest value of b/h at which the folding table is in equilibrium. The coefficients of static friction are 0.5 at A and 0.3 at C. Neglect the weight of the table.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.