The Reynolds number can be viewed as the ratio of (a) Drag force/Dynamic force (b) Buoyancy force/Viscous force (c) Wall friction force/Viscous force (d) Inertial force/Gravitational force (e) Inertial force/Viscous force

The Reynolds number can be viewed as the ratio of (a) Drag force/Dynamic force (b) Buoyancy force/Viscous force (c) Wall friction force/Viscous force (d) Inertial force/Gravitational force (e) Inertial force/Viscous force

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.22P

See similar textbooks

Related questions

Q: Explain the the mechanical efficiency of a fan is the ratio of the rate of increase of the…

A: Kinetic energy is only mechanical energy of air . If we consider a fan to which we give some power…

Q: Water at 10 Cflows from a large reservoir to a smaller one through a 5-cm diameter cast iron piping…

A: Given Diameter of the pipe = 5 cm = 0.05 m Flow rate = 6L/s Density = 999.7 kg/ms Friction…

Q: A 10-cm-diameter cylindrical shaft rotates inside a 50-cm-long 10.3-cm diameter bearing. The space…

A: Assumption: Oil between shaft and bearing is Newtonian and Incompressible fluid.

Q: Oil with density 905 kg/m^3 and viscosity 2.33 kg/m.s flows in a 430 meter long 42-cm-diameter…

Q: a pipe of diameter 60 mm is subjected to an oil flow at rate of 343.5 kg/s. the mass density and…

A: Pressure gradient in the pipe is 1080 kPa/m.

Q: In the design of small scale bioprocess plant, a shear sensitive Newtonian liquid of density 1100…

A: Given: Density of the liquid is 1100 kg/m3. Viscosity of the liquid is 0.015 Nsm-2. Flow rate of the…

Q: rite the definition ,formula and significance of Reynolds number and Grashoff number in convection…

A: Given: Reynolds number Grashoff number To write: The formula, definition and significance of in…

Q: What is the air pressure (kpa) in a car tier

Q: The clutch system shown in the figure is used to transmit torque through a 2-mm-thick oil film with…

A: Given: toil=2 mmμ=0.38 Ns/m2d=30 cmN1=1200 rpmN2=1125 rpm

Q: What is the friction loss in cm of water in a 2.44m diameter chimney 61m high up which gas is…

A: Givend=2.44ml=61mV=9.14m/secρ=0.6776kg/m3

Q: A liquid flows through a 200 m long pipe with a rectangular cross section with 0.6mX0.3m dimensions.…

A: Length of the pipe, L=200m Cross-sectional area of rectangular section, A=0.6m*0.3m=0.18m2 The…

Q: A gasoline engine is at a location where the temperature is measured to be 14.8 °C and produces 300…

A: Gasoline engine: The internal combustion engine that runs on gasoline has the combustion chamber…

Q: i need the answer quickly

Q: The clutch system shown in Fig is used to transmit torque through a 2-mm-thick oil film with ? =…

A: Given data: Speed of driving shaft, N1 = 1200 rpm Speed of driven shaft, N2 = 1125 rpm Thickness of…

Q: The types of fluid which have viscosity and in practice is Ideal fluid Real fluid O Non-Newtonian…

A: Option B is the right answer.

Q: The actual velocity of a gas entering in a chimney is 8 m/sec. the gas temperature is 25%C and…

A: V=velocity of a gas=8 m/sT=Gas temperature=25°C=273.15+25=298.15 KP=Gas Pressure=98kPaR=Gas…

Q: The difference in pressure (in N/m²) across an air bubble of diameter 0.001 m immersed in vater…

A: Given data: D= 0.001 m T = 0.072 N/m Need to determine the pressure difference across the air…

Q: A gasoline engine is at a location where the temperature is measured to be 14.2 °C and produces 347…

A: Gasoline engine: The gasoline engine is an internal combustion engine in which the air-fuel…

Q: Consider the steady, incompressible, viscous and fully-developed flow through a horizontal circular…

Q: Write a short note on significance of various dimensionless numbers in heat transfer.

A: Heat transfer: According to thermodynamics law's, heat can be transfer from one part to another .…

Q: (c) The diameter of the piston and qutletof the paint sprayer in Fig. 1 is 6 cm and 0.5 cm,…

Q: System's heat transfer rate Overall heat coefficient (U) based on outside surface area Prandtl (Pr),…

Q: An coconut oil (considered as viscous fluid) must be pumped between two buildings in an…

A: Given data: The oil flow rate is m = 20 kg/s. The liquid will be heated to temperature of To = 40…

Q: 17- What size unit is kg/s? O A) Volume by mass O B) Mass flow rate O 9 Dynamic viscosity O D)…

A: Correct option: B. Mass flow rate

Q: Fresh water and sea water flowing in parallel horizontal pipelines are connected to each other by a…

Q: In the design of small-scale bioprocess plant, a shear sensitive Newtonian liquid of density 1100…

A: As per the question mentioned, it is a shear sensitive Newtonian liquid , it mean it is case of…

Q: In a reservoir system with a very large accumulation volume for the idea a) Since the diameter of…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: A 25mm diameter steel cylinder 300 mm long falls, because of its own gravity force at a uniform rate…

Q: Derive an expression for the change in height h in a circular tube of a liquid with surfacetension Y…

A: Given Data: The surface tension is Y. The contact angle is θ. The radius of the capillary tube is…

Q: As3...Air at atmospheric pressure, 27 °C and %30 RH conditions and with a velocity of 3 m/s flows…

A: Given: The temperature of air, T1 = 27°C The relative humidity of air, w1 = 30% The area of pool, A…

Q: Water (with a viscosity µ of 0.00958 N.s/m²) is flowing in a pipe with a diameter of 10 cm at a dish…

Q: Relationship between fluid flow and convection heat transfer

A: The motion of the fluid subjected to the unbalanced forces is called as fluid flow. As long as the…

Q: ition Reynolds number for flow in a circular pipe is Re=2300. For flow through a 5-cm-diameter pipe,…

A: Givenreynold number Re=2300diameter of pipe d=5cm=0.05mtemperature T=20oCthe Kinematic Viscosity of…

Q: Define the following terms and provide an example in each case d. Reynolds experience and Reynolds…

A: REYNOLDS EXPERIMENT:- The Osborne Reynolds experiment is used to demonstrate laminar and turbulent…

Q: Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizont a pump…

A: Fluid Mechanics And Use Of Moody Chart

Q: a pipe of diameter 60 mm is subjected to an oil flow at rate of 343.5 kg/s. the mass density and…

A: we will use Hagen–Poiseuille equation for solving this question

Q: Q3 Glycerin at 40°C with density of 1252 kg/m³ and viscosity of 0.27 kg/m.s is flowing through a…

A: Find, Pumping power. Pressure drop.

Q: Explain the concept of heat transfer, and spontaneity and probability base on the increasing…

A: Heat transfer can be defined as the process of transfer of energy in which molecules are moved from…

Q: This hermodynamics statement is false to say that a basic way to reduce the mean velocity of water…

A: Given statement: A basic way to reduce mean velocity of water flowing through a pipe for a given…

Q: Local Nusselt number for fully developed (hydrodynamically and thermally) turbulent flow in a smooth…

A: Write the given expression of Local Nusselt Number. NuD=A×ReDB×PrC ...... (1)

Q: Determine the bulk modulus of clasticity of a fluid which is compressed in a cylinder from a volume…

A: Since you have asked multiple questions in a single request, we would be answering only the first…

Q: Local Nusselt number for fully developed (hydrodynamically and thermally) turbulent flow in a smooth…

A: Given question: Express the local Nusselt number using Reynold's and Prandtl Numbers in the formNuD…

Q: Compare the capillary effect of immersion in (i) water and (ii) mercury of a glass tube of 6 mm…

A: Given Data, D = Internal diameter of capillary tube = 0.006 m σw= Surface tension for water = 0.0725…

Q: Methanol at a temperature of 30°C flows in a horizontal brass pipe of 3 cm diameter with a flow rate…

Q: What is the relationship between the fluid viscosity and the drag force?

Q: Process water flows at a velocity of 6 m/s through a 10 cm ID 90° elbow. Pressure was measured to be…

Q: Explain why the friction factor is independent of the Reynolds number at very large Reynolds…

A: As we know reynolds number Re=ρνDμwhereρ=density of fluid V= velocity of fluid μ=viscosity of fluid…

Q: H.W.2 /: Consider a 55cm long journal bearing that is lubricated with oil whose viscosity is 0.1…

Q: Fluid with a density of 602 kg/m³ flows inside a 3.3 cm diameter tube at a velocity of 1.7 m/s. The…

A: The convection heat transfer coefficient: h = 3755 W/m2•K

Q: For the case of turbulent flow in rough pipes, does the friction factor depend on the Reynolds…

A: For the case of turbulent flow in rough pipes, the friction factor depend on the Reynolds number.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Oil with density 905 kg/m^3 and viscosity 2.33 kg/m.s flows in a 430 meter long 42-cm-diameter horizontal pipeline at an average velocity of 0.7 m/s. Determine the pumping power required in kW to overcome the pressure losses and to maintain the flow of oil in the pipe. Make sure to check Reynolds number first to identify the type of flow and use the proper equation.
How is volume flow rate different than velocity? What happens to volume flow rate in areas where fluid pressure is high?
Derive an expression for the change in height h in a circular tube of a liquid with surfacetension Y and contact angle θ , as in Fig. E1.8.
What is the general difference between the coefficient of volume expansion of solids and liquids? Explain
Consider a fluid with a Prandtl number of 7 flowing through a smooth circular tube. Using the Colburn, Petukhov, and Gnielinski equations, determine the Nusselt numbers for Reynolds numbers at 3500, 104, and 5 * 105. Compare and discuss the results.
What should be the maximum radius of a pipe, to ensure that a liquid with a density of 5 g/cm^3 and a viscosity of 0.00522 kg/m*s, flowing horizontally at a velocity of 60 cm/s in laminar flow through the pipe at a temperature of 4°C?
Rank in order, from highest to lowest, the liquid heights h1 to h4 in tubes 1 to 4. The airflow is from left to right.
in convection heat transfer, what happen to the heat transfer coefficient if the viscosity of the fluid decrease?
Which of the three transport processes (momentum transfer, heat transfer, and mass transfer) is regarded the resistance? Choose 1. Temperature, pressure, viscosity, or length of transport
A liquid flows through a 200 m long pipe with a rectangular cross section with 0.6mX0.3mdimensions. The dynamic viscosity of the liquid is 2.33 kg/ms and the density is 894 kg/m3. Ifthe average velocity of the fluid is 0.8m/s what is the necessary pumping power in kW tomaintain the flow of the liquid?
An coconut oil (considered as viscous fluid) must be pumped between two buildings in an agro-industrial plant through an AISI 304 stainless steel pipe spread on the ground that has an outside diameter of 22 cm and 110 m long. To facilitate pumping, the liquid will be heated to 40 ° C in order to reduce its viscosity. The oil flow rate will be 20 Kg / s and the specific heat will be 1300 J / Kg K. Determine the temperature drop that the liquid will experience along the pipeline under the following operating conditions:Ambient air temperature = 10 ° CWind speed = 14 m / sPipe surface temperature = 37 ° C
What is the Reynolds number of a fluid flowing in a tube with an inside diameter of 1 inches? The viscocity is 1.353 x 10^ -5 lb/ft-s and the mass flow rate is 79 lb/h.Correct Answer: 24,780.96 ± 1%