In the design of small scale bioprocess plant, a shear sensitive Newtonian liquid of density 1100 kg/m2, and viscosity 0.015 Nsm is to be transported along a length of pipe at a rate of 4.3 litter per minute. Determine the diameter of the pipe required if the pressure drop along the pipe is not to exceed 100 Nm2 per meter length.

In the design of small scale bioprocess plant, a shear sensitive Newtonian liquid of density 1100 kg/m2, and viscosity 0.015 Nsm is to be transported along a length of pipe at a rate of 4.3 litter per minute. Determine the diameter of the pipe required if the pressure drop along the pipe is not to exceed 100 Nm2 per meter length.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

It is desired to determine the surface tension of a particular fluid using a capillary-riseexperiment. Kienth used a 0.5 mm glass tube and found that the height of the liquidmeasured 30 mm with a contact angle of 30°. Kienth then performed viscosity measurements using an Ostwald viscometer. He found that the fluid takes 1.5 times slowerto flow through the viscometer relative to water with a density of 1000 kg/m? and aviscosity of 1.0 cP. It is previously known that the viscosity of the fluid is 1.35 cP. Whatis the surface tension of the liquid?
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 ?2/? and SG=0.9. Find the frictional resistance exerted by the oil on the shaft in Newtons (N). And when the shaft is fixed axially and rotated inside the sleeve at 2000 rpm, determine the resisting torque exerted by the oil and the power required to rotate the shaft in kiloWatts (kW).
Glycerin, with a density of 1260 kg/m3 and an absolute viscosity of 1.5 kg/m.s, flows in a tube with an internal diameter of 5,0 cm, but it is not known whether the regime is laminar or turbulent. Knowing that the length of the hydrodynamic inlet of this flow is 0.2 m, determine the velocity of the oil and the flow regime. (the form is in the side picture)
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 ?2/? and SG=0.9. Find the frictional resistance exerted by the oil on the shaft in Newtons (N).
Honey at 1L/min is flowing in a capillary viscometer 2cm in diameterand 50cm long. If the pressure drops is 40kPa, determine its viscosity
An 18-kg slab slides down a 15° inclined plane on a 3-mm-thick film of oil with viscosity of 0.0814Pa-sec. If the contact area is 0.3m^3, find the terminal velocity of the slab. Neglect air resistance. ans. 5.614 m/s
Sulfuric acid with a density of 1980 kg / m3 and a viscosity of 26.7 cP flows in a pipe with a diameter of 35 mm. If the acid flow rate is 2 m3 / min, what is the pressure loss due to friction in a 30 m long smooth pipe? a. Reynold number = Answer. b. Loss of Pressure = AnswerkPa.
A 5-mm-diameter capillary tube is used as a viscometer foroils. When the flow rate is 0.071 m3/h, the measured pressuredrop per unit length is 375 kPa/m. Estimate the viscosityof the fluid. Is the flow laminar? Can you also estimate thedensity of the fluid?
A sleeve of 10cm encases a vertical metal rod 3.0cm in diameter with radial clearance of 0.02mm. if when immersed in oil of viscosity 6.0 poise , the effective weight of the sleeve is 7.5N , will the sleeve slide down the rod and if so, at what velocity?
A pipeline 0.5 m diameter and 1200 m long is used for transporting an oil of density 150 kg/m3 and of viscosity 0.91 Pa-s at 0.4 m2/s. If the roughness of the pipe is 0.5 mm, what is the pressure drop?
An oil gusher shoots crude oil 23.0 m into the air through a pipe with a 0.100 m diameter. Neglecting air resistance but not the resistance of the pipe, and assuming laminar flow, calculate the pressure (in N/m2) at the entrance of the 45.0 m long vertical pipe. Take the density of the oil to be 900 kg/m3 and its viscosity to be 1.00 (N/m2) · s (or 1.00 Pa · s). Note that you must take into account the pressure due to the 45.0 m column of oil in the pipe.
steel tape 0.5 mm thick and 20 mm wide is pulled by a force F through a slit opening 1.5 mm and length 15 mm. Considering that the tape is centered on the slit, that lubricating oil of viscosity µ = 0.4 Nm-2s? fills the gap spaces not occupied by the tape and that the maximum tape speed is 10 m/s, calculate the maximum force F. Expected Answer: Maximum Force = 4.8N