EXAMPLE:9. The rigid bar ABC shown in thefigure is hinged at A andsupported by a steel rod at B.Determine the largest load P thatcan be applied at Ċ if the stress inthe steel rod is limited to 30 ksiand the vertical movement of endC must not exceed 0.10 in.(Practice at Home)2 ftSteelL=4 ftA=0.50 in²E = 29 x 10° psi3 ft

Given data as per the question stress in steel bar =30 ksivertical moment of C =0.10 inlength of…

The rigid bar ABC shown in the figure is hinged at A and supported by a steel rod at B. Determine the largest load P that can be applied at C if the stress in the steel rod is limited to 30 ksi and the vertical movement of end C must not exceed 0.10 in. (Practice at Home) Steel A-0.50 in² E=29-10° p 3 ft

The rigid bar ABC shown in the figure is hinged at A and supported by a steel rod at B. Determine the largest load P that can be applied at C if the stress in the steel rod is limited to 30 ksi and the vertical movement of end C must not exceed 0.10 in. (Practice at Home) Steel A-0.50 in² E=29-10° p 3 ft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.6.1P: A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned...

See similar textbooks

Similar questions

A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression is 400 MPa. The total load P that may be supported by the pad is 900 kN. Using a factor or safely 3.0 with respect to ultimate strength, determine the outer diameter of the pier if the thickness, is of the cross section is 12 mm.
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
, An arm A BC lying in a horizontal plane and supported at A (see figure) is made of two identical solid steel bars AB and BC welded together at a right angle. Each bar is 22 in. long. (a) Knowing that the maximum tensile stress (principal stress) at the top of the bar at support A due solely to the weights of the bars is 1025 psi, determine the diameter d of the bars. (b) If the allowable tensile stress is 1475 psi and each bar has a diameter d = 2.0 in,, what is the maximum downward load P that can be applied at C(in addition to self-weight
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
Because of foundation settlement, a circular tower is leaning at an angle a to the vertical (see figure). The structural core of the tower is a circular cylinder of height ft, outer diameter d2, and inner diameter d1.For simplicity in the analysis, assume that the weight of the tower is uniformly distributed along the height. Obtain a formula for the maximum permissible angle a if there is to be no tensile stress in the tower.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A solid bar of circular cross section (diameter d) has a hole of diameter d/5 drilled laterally through the center of the bar (sec figure). The allowable average tensile stress on the net cross section of the bar is s allow. (a) Obtain a formula for the allowable load P allowthat the bar can carry in tension. (b) calculate the value of P allowif the bar is made of brass with a diameter d = 1.75 in. and s allow= 12 ksi. Hint: Use the formulas of Case 15. Appendix E.
A steel column (E = 30 x 103 ksi) with pinned ends is constructed of a W10 x 60 wide-flange shape (sec figure). The column is 24 ft long. The resultant of the axial loads acting on the column is a force P acting with an eccentricity n = 2.0 in. If P = 120 kips, determine the maximum compressive stress ff^ in the column. Determine the allowable load Pallowif the yield stress is ( y =42 ksi and the factor of safety with respect to yielding of the material is n = 2.5.
A short column constructed of a W 12 × 35 wide-flange shape is subjected to a resultant compressive load P = 25 k having its line of action at the midpoint of one flange (see figure). Determine the maximum tensile and compressive stresses d1and d2., respectively, in the column. Locate the neutral axis under this loading condition. Recompute maximum tensile and compressive stresses if a C 10 × 15.3 is attached to one flange, as shown.
A W14 × 53 wide-flange column of a length L = 15 ft is fixed at the base and free at the top (see figure). The column supports a centrally applied load = 120 kips and a load P2= 40 kips supported on a bracket. The distance from the centroid of the column to the load P2is s = 12 in. Also, the modulus of elasticity is E = 29,000 ksi, and the yield stress is y= 36 ksi. Calculate the maximum compressive stress in the column, Determine the factor of safety with respect to yielding.
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
AW310 × 74 wide-flange steel column with length L = 3.8 m is fixed at the base and free at the top (see figure). The load P acting on the column is intended to be centrally applied, but because of unavoidable discrepancies in construction, an eccentricity ratio of 0.25 is specified. Also, the following data are supplied: E = 200 GPa, y = 290 MPa, and P = 310 kN. What is the maximum compressive stress max in the column? What is the factor of safety n with respect to yielding of the steel?