The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 12 mm. If the normal stress in rod (1) must not exceed 225 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm. Dota A Answer: W = ↓↓ a i 1 B W b (1) ↓↓ kN/m 9

The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 12 mm. If the normal stress in rod (1) must not exceed 225 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm. Dota A Answer: W = ↓↓ a i 1 B W b (1) ↓↓ kN/m 9

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 115 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 3 mm, and an allowable normal stress of 65 MPa. Assume x3 = 3.7 m, x2 = 1.5 m, and y; = 4.1 m, Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (σY)st=680 MPa, and for the bronze (σY)br=490 MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa.
A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having a weight of 800 lb. The elevator is 150 ft below the drum and is descending at the constant rate of 3 ft>s when the drum suddenly stops. Determine the maximum stress developed in the cable when this occurs. Est = 29(103) ksi, sY = 50 ksi.
2. A steel wire 30 ft long, hanging vertically, supports a load of 500 lbf. Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed 20,000 psi and the total elongation is not to exceed 0. in. Assume E = 29 × 106 psi.
A 150-mm-long bronze tube, closed at its ends, is 80 mm in diameter and has a wall thickness of 3mm. it fits without clearance in an 80-mm hole in a rigid block. The tube is then subjected to an internal pressure of 4.00 MPa. Assuming v=1/3 and E= 83 GPa, determine the tangential stress in the tube.
The rigid beam is supported by the three suspender bars. Bars AB and EF are made of aluminum and bar CD is made of steel. If each bar has a cross-sectional area of 450 mm2, determine the maximum value of P if the allowable stress is (sallow)st = 200 MPa for the steel and (sallow)al = 150 MPa for the aluminum. Est = 200 GPa, Eal = 70 GPa.
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 12 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 95 MPa, and the bearing stress between the rod head and the support plate cannot exceed 135 MPa. Determine the maximum value of Pmax that can be supported by the structure.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm If the yield stress for the steel is (σY)st=610MPa, and for the bronze (σY)br=490MPa(, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa.
The outside diameter of the steel pipe shown is 220 mm and its wall thickness is 6.0 mm. The upper bearing plate has the same width as the reinforced concrete beam it supports. The total load on the column by the reinforced concrete beam is 550 kN. Determine: A. The length L of the rectangular upper bearing plate if its width is 275 mm. and the average bearing stress between the steel plate and the reinforced concrete beam is not to exceed 6.2 MPa.
The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A, B, C, and D exert only vertical forces on the beam, determine the required diameter of the bolt at B and the required outer diameter of its washers if the allowable tensile stress for the bolt is 1st2allow = 150 MPa and the allowable bearing stress for the wood is 1sb2allow = 28 MPa. Assume that the hole in the washers has the same diameter as the bolt.
A suspension system of a mountain bike is held by a pin at point C and supported by a shock absorber BD. If the bike is designed to withstand a load P = 1500N with safety factor F₁ = 2, ultimate shear stress t = 150 MPa and ultimate tensile stress Ou = 360 Mpa, determine pin B and pin C diameters.
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 7 mm2. The cross-sectional area of rod (2) is 18 mm2. For a uniformly distributed load of w = 2.7 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 5.65 m.