The rigid beam is supported by a pin at A and wires BD and CE (made of steel, E=200 GPa, and the cross sectional area is 1500 mm“). If the distributed load (W) causes the end C to be displaced 10 mm downward, determine: a- the normal strain developed in wires CE and BD. b- the normal stress developed in wires CE and BD. c- the value of the distributed load (W). 15m

The rigid beam is supported by a pin at A and wires BD and CE (made of steel, E=200 GPa, and the cross sectional area is 1500 mm“). If the distributed load (W) causes the end C to be displaced 10 mm downward, determine: a- the normal strain developed in wires CE and BD. b- the normal stress developed in wires CE and BD. c- the value of the distributed load (W). 15m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.4P: An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy =...

See similar textbooks

Similar questions

An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 20°. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
The head H is connected to the cylinder of a compressor using six 316-in. diameter steel bolts. If the clamping force in each bolt is 800 lb, determine the normal strain in the bolts. If sY = 40 ksi and Est = 2911032 ksi, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released?
5 decimal places Determine the total strain (mm/mm) of a 2.64-m bar with a diameter of 21 mm subjected to a tensile force of 71 kN at a temperature increase of 49 C°. Consider the α=27.3 µm/mC° and E = 122 GPa.
The rigid beam is supported by a pin at A and wires BD and CE. If the load P on the beam causes the end C to be displaced 15 mm downward, determineA. the normal strain developed in wire CEB. the normal strain developed in wires BD. Show free body diagram and complete solution (no shortcut) SHOW PRESSURE DIAGRAM. THANK YOU
6. A prismatic bar of length L is subjected to axial load P. Determine the maximum strain & along the bar length, given that the axial displacement along the member length varies according u = (12/L) × 10-3.
The aluminum rod AD (E=73 GPa, 0=23x10°6/°C) has a diameter of 15 mm and isattached to the rigid support at A when the temperature T; = 30°C. If thetemperature becomes T: = -20°C, and the axial loads are applied to the rod asshown, determine: a) The location and magnitude of the maximum stress acting on the rod ADb) Displacement of point Dc) Average strain in part BC
A tri-axial state of stress, σx , σy, and σz ,exists in a steel machine part. For steel, E = 200GPa and ν = 0.3. Determine the normal strain in the x-direction if σx = 100MPa, σy = 35MPa, σz = 70MPa. Determine the dilatation. Determine the modulus of rigidity.
The state of strain at a point on a wrench has components ϵx = 120(10-6), ϵy = -180(10-6), γxy= 150(10-6). Use Mohr's circle to solve the problem. Determine the orientations of the element at which the principal strains occur. θp1= θp2=
A rigid steel bar is supported by three rods, as shown. There is no strain in the rods before the load P is applied. After load P is applied, the normal strain in rod (2) is 1020 μin./in. Assume initial rod lengths of L1 = 148 in. and L2 = 78 in. Determine(a) the normal strain in rods (1).(b) the normal strain in rods (1) if there is a 0.043 in. gap in the connections between the rigid bar and rods (1) at joints A and C before the load is applied.(c) the normal strain in rods (1) if there is a 0.043 in. gap in the connection between the rigid bar and rod (2) at joint B before the load is applied.
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm2. The cross-sectional area of rod (2) is 18 mm2. For a uniformly distributed load of w = 2.4 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 5.25 m.
The force P causes point A to be displaced vertically by 1.60 mm A) Determine the normal strain developed in wire AB B) Determine the normal strain in wire AC
A rectangular block has dimensions of 3 in, 4 in, and 5 in along the X-, y-, and z- axes, respectively. The block is subjected to triaxial loading of three uniformly distributed loadings of 30 kips (C), 45 kips (T), and 60 kips (C) along the x-, y-, and z- axes, respectively. If the strain along the X- axis and the z-axis are 0.00021 (C) and 0.00042 (T), respectively, determine the Poisson's ratio and the modulus of elasticity of the material. Also, what is the change in volume of the material?