300 mm--300 mm-150 kN/mThe rigid beam shown in Fig. 4-19a is fixed to the top of the threeposts made of A-36 steel and 2014-T6 aluminum. The posts each havea length of 250 mm when no load is applied to the beam, and thetemperature is T, = 20°C. Determine the force supported by eachpost if the bar is subjected to a uniform distributed load of 150 kN/mand the temperature is raised to T2 = 80°C.60 mm-250 mm-40 mm40 mm--SOLUTIONSteelAluminumSteel

For 2014 -T6 aluminiumE=73.1GPaα=23×10-6 (Temperature Coefficient)For A-36 steel…

The rigid beam shown in Fig. 4-19a is fixed to the top of the three posts made of A-36 steel and 2014-T6 aluminum. The posts each have a length of 250 mm when no load is applied to the beam, and the temperature is T1 = 20°C. Determine the force supported by each post if the bar is subjected to a uniform distributed load of 150 kN/m and the temperature is raised to T = 80°C. -300 mm--300 mm- 150KN/m 60 mm- 250 mm -40 mm 40 mm- SOLUTION Steel Aluminum Steel

The rigid beam shown in Fig. 4-19a is fixed to the top of the three posts made of A-36 steel and 2014-T6 aluminum. The posts each have a length of 250 mm when no load is applied to the beam, and the temperature is T1 = 20°C. Determine the force supported by each post if the bar is subjected to a uniform distributed load of 150 kN/m and the temperature is raised to T = 80°C. -300 mm--300 mm- 150KN/m 60 mm- 250 mm -40 mm 40 mm- SOLUTION Steel Aluminum Steel

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The steel framework is used to support the reinforced stone concrete slab that is used for an office. The slab is 200 mm thick. Sketch the loading that acts along members BE and FED. Take a = 2 m, b = 5 m. Hint: See Tables 1.2 and 1.4.
The given the following elements of a T-beam: Length 4m Flange thickness = 110mm Concrete strength 30MPa. Steel Yield strength = 414MPa Width of the web = 310mm Effective depth = 460mm If the beam is reinforced for tension only, determine the following: a. The balanced steel area b. The nominal and ultimate balanced moment capacity c. The maximum steel area d. The nominal and ultimate maximum moment capacity e. The required Steel Area to carry MDL= 120kN,m, MLL-60kN.m
Determine the nominal moment strengt of the irregular beam shown. Assume the area of 25 mm rebar is 510 sq. mm. Given: a.) fc' = 35 MPa; fy= 413.70 MPa b.) fc' = 21 MPa; fy = 413.70 MPa
The rigid beam is supported by the three posts A, B, and C of equal length. Posts A and C have a diameter of 75 mm and are made of a material for which E = 70 GPa and sY = 20 MPa. Post B has a diameter of 20 mm andis made of a material for which E = 100 GPa and sY = 590 MPa. Determine the smallest magnitude of P so that (a) only rods A and C yield and (b) all the posts yield.
A reinforced concrete beam has a width of 425mm and an effectivedepth of 900mm. The longitudinal bars at compression side are 4-25mm dia. and 2layers of 4-32mm dia. at tension side. Concrete strength f’c=27.60 MPa and fy=420.4) Calculate the Transformed moment of Inertia.5) Calculate the moment capacity of the section.6) Calculate for the safest uniform load that can carry by the beam if ihas a lengthof 10m.
Completely solve and box the final answer. Illustrate the problem. Write legibly 4. Compute the safe concentrated load P that the beam could carry at a distance of 1 m from the fixed support with a span of 4 m from the arrangements shown below. The beam is made up of four 50 mm by 200 mm section framed. The allowable shearing stress of the beam is 0.70MPa.
The overhanging beam shown supports the given ultimate load Wu= 5okN/m. The section is 300mm by 500mm rectangular beam having f'c=35MPa, fy=420 MPa, stirrups diameter = 10mm and concrete cover 40mm. a.) the area of steel reinforcement corresponding to rho max in mm2.b.) the location of the point of zero shear in the beam measured from the left support B in mm.c.) Calculate the maximum positive moment in the beam in kN.m.d.) Calculate the required reinforcement Asreqd corresponding to the maximum positive moment in mm2.e.) Calculate the depth of the compression block of the final positive moment section in mm.f.) Calculate the depth of the neutral axis of the final positive moment section in mm.g.) What is the ultimate moment capacity of the final positive moment section in kN.m.h.) Calculate the additional positive moment that can be imposed to the beam without exceeding the moment capacity of the final positive moment section in kN.m.
Calculate the ultimate moment capacity of a rectangular beam with b = 300 mm, d = 500 mm, As= 5400 mm2• Assume fc = 34 MPa, fy = 414 MPa.
QUESTION1) Figure Q1(a) show a simply supported beam of length L = 4.8m is and built for placing Machine and Magnum frame. The combined weight of the machine is approximated by uniform load 90kN/m along x3 = 2.4 m. For of the design, its assumed that the column framed located at a distance x1 and x2 = 0.8m and resulting concentrated load P1 and P2 exerted oneach beam is taken as 150kN and 150kN, respectively. The cross section of beam show as in Figure Q1(b). (a) Determine the bending stress at point a and the maximum bending stress of the beam (b) By referring Figure Q1(a) and consider section n-n, determine the maximum shear stress and the shear stress at point a.
The load is supported by the four 304 stainless steel wires that are connected to the rigid member's AB and DC. Determine the angle of tilt of each member after the 500-lb load is applied. The members were originally horizontal, and each wire has a cross-sectional area of 0.025 in2.
s shown in the sketch, an interior column AB in a steel frame carries a factored axialcompressive load, Pu = 1540 kips. The column is braced at the top and bottom and the mid-height in the perpendicular plane, and sidesway in the plane of the steel frame is allowed. Thecolumns are 12-ft long, and the columns above and below the column AB are the same size asAB. The adjacent girders are W 18×50 and are 32-ft long. Use A992 steel with Fy = 50 ksi,select the lightest W-section for the column AB. Use stiffness reduction factor where applicable.
The rigid beam is supported by a pin at C and an A992 steel guy wire AB of length 6 ft. If the wire has a diameter of 0.2 in., determine the distributed load w if the end B is displaced 0.12 in. downward. The wire remains elastic.