The rod has a radius of 4 m. (Figure 1) Figure 1 of 1 > ▾ Part A Determine the smallest force F that must be applied along the rope in order to cause the curved rod to fail at the support A. This requires a moment of M 1400 Nm to be developed at A. Express your answer t three significant figures and include the appropriate units. DH μÀ ?

The rod has a radius of 4 m. (Figure 1) Figure 1 of 1 > ▾ Part A Determine the smallest force F that must be applied along the rope in order to cause the curved rod to fail at the support A. This requires a moment of M 1400 Nm to be developed at A. Express your answer t three significant figures and include the appropriate units. DH μÀ ?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.4P: The inclined ladder AB supports a house painter (85 kg) at C and the weight iq = 40 K/m} of the...

See similar textbooks

Similar questions

The following shaft, having a diameter of 20 mm, is made of steel (Sut = 520 MPa, Se = 260 MPa) and is subjected to a fully reversed transverse force F = 120 N and a fully reversed torque T = 60 N.m. The shaft is fixed at its left end. Find the factor of safety at A for infinite lifetime using the modified Goodman diagram.
A steel shaft 100mm in diameter is loaded and support in shaft bearing 0.4m apart. The shaft carries three loads: first mass 12kg at the centre, second mass 10kg at a distance 0.12m from the left bearing and third mass of 7kg at a distance 0.09m from the right bearing. Find the value of the critical speed by using Dunker ley’s method if E = 2X1011N/m2.
Calculate the maximum force P that can be applied in a phosphor bronze spring having mean diameter of 150 mm and consisting of 24 turns of 10-mm diameter wire when the spring is stretched 180mm. Use G = 42 GPa. Group of answer choices 233.11 N 113.33 N 116.667 N 225.56 N
A 5 hp motor with a speed of 900 rpm is used to drive an industrial fan with a velocity of 5.72m/s. The center distance between the sprockets is 1.5 times the diameter of driven sprocket andis equal to 630 mm. Determine the length of chain in pitches. Use RC 40 chain and service factorof 1.3.
A belt drive is used to transmit power from an electric motor to a compressor for a refrigerated truck. The compressor must still operate when the truck is parked and the engine is not running. The 50-hp electric motor is rated at 150+X rpm (where value of X = 50), and the motor sheave diameter is 5+d1 in. (where value of d1 = 5). The compressor sheave has 8+d2 in (where value of d2 = 5) diameter. The center distance of the drive is 15 in. Determine the appropriate industrial V belt size, the length of belt, operating speed of compressor and belt speed.
Can anyone help me with this question. The Motor (J1=0.46 kg‐m2) is connected to a gearbox (J2 =0.27 kg‐m2 and J3=0.17 kg‐m2) by a steel shaft. The output of the gearbox is connected to a turbine (J4=0.37 kg‐m2 by a second steel shaft. The shafts are supported by bearings (not shown). The gearing in the gearbox is such that theta3=‐2.7theta2. Use Lagrange methods to determine the equation of motion for the system including the flexibility of the shafts, using variables of theta 1, theta 3, theta 4 based on changing theta 3.
der engine has been drawn 0 2 moment diagram for a multicylin ~ 2.4° horizontallv. e = 4500 N-m vertically and 1 mm 'mxemapwd areas between output torque curve and the mean resistance line taken in order from one end are 342. 23, 245. 303. 115. 232. 227. 164 mm2. when the engine is running at 150 r.p.-m- If the mass of the flywheel is 1000 kg and the tota! fluctuation of speed does not exceed 3% of the mean speed. find the minimum value of the radius of gyration 16.4/ The turning
A vertical shaft is supported by two deep groove ball bearings as shown below. The shaft will be driven by vee belts through a pulley. The combined tensions of the belt apply and the weight of the pulley assembly applies a force of 5.4kN and 900N respectively. The shaft has a diameter of 32mm. Bearing A at the top supports the shaft radially whereas bearing B at the bottom supports the shaft axially and radially. Two deep groove ball bearings have been selected for this application. The models of the bearings are SKF 6305 and SKF 6205 for bearing A and B respectively. a) What are the forces at bearing A and B? b) Paste a screenshot of the graph showing the distribution of the forces in the shaft. c) From the report, find the static load capacity for: Bearing A Bearing B
A bar is attached to the spring at the point C. The left end of the bar is pin supported and can rotates about the pin at Point A. The mass of the bar is m=20kg. The total length of the bar is LAB=3m and LAC=2m. Point A is 0.6 m below the ceiling. A clockwise constant couple moment M= 30Nm is applied on the bar so that the bar rotates from the horizontal position with θ=0° to the vertical position with θ=90°. The spring always maintains at the vertical position. The spring’s stiffness coefficient is k=30N/m and its unstretched length is 0.5 m. The acceleration due to gravity g=9.81 m/s2. During the process that the bar rotates from the horizontal position to the vertical position, determine the following. (4) the work done by the reaction force of the pin.____________ (J)
A bar is attached to the spring at the point C. The left end of the bar is pin supported and can rotates about the pin at Point A. The mass of the bar is m=20kg. The total length of the bar is LAB=3m and LAC=2m. Point A is 0.6 m below the ceiling. A clockwise constant couple moment M= 30Nm is applied on the bar so that the bar rotates from the horizontal position with θ=0° to the vertical position with θ=90°. The spring always maintains at the vertical position. The spring’s stiffness coefficient is k=30N/m and its unstretched length is 0.5 m. The acceleration due to gravity g=9.81 m/s2. During the process that the bar rotates from the horizontal position to the vertical position, determine the following. (2) ) the work done by the couple moment. __________(J) (two decimal places)
A bar is attached to the spring at the point C. The left end of the bar is pin supported and can rotates about the pin at Point A. The mass of the bar is m=20kg. The total length of the bar is LAB=3m and LAC=2m. Point A is 0.6 m below the ceiling. A clockwise constant couple moment M= 30Nm is applied on the bar so that the bar rotates from the horizontal position with θ=0° to the vertical position with θ=90°. The spring always maintains at the vertical position. The spring’s stiffness coefficient is k=30N/m and its unstretched length is 0.5 m. The acceleration due to gravity g=9.81 m/s2. During the process that the bar rotates from the horizontal position (state 1) to the vertical position (state 2), determine the following. 5) when use T to represent kinetic energy, V potential energy, U work done and if the bar is at rest at state 1, the principle of work-energy in this case could be expressed as____________ . V1+∑U(1-2)=T2+V2 T1+V1=T2+V2…
A bar is attached to the spring at the point C. The left end of the bar is pin supported and can rotates about the pin at Point A. The mass of the bar is m=20kg. The total length of the bar is LAB=3m and LAC=2m. Point A is 0.6 m below the ceiling. A clockwise constant couple moment M= 30Nm is applied on the bar so that the bar rotates from the horizontal position with θ=0° to the vertical position with θ=90°. The spring always maintains at the vertical position. The spring’s stiffness coefficient is k=30N/m and its unstretched length is 0.5 m. The acceleration due to gravity g=9.81 m/s2. During the process that the bar rotates from the horizontal position to the vertical position, determine the following. (3) the potential energy of the spring when AB is vertical__________(J)