A bar is attached to the spring at the point C. The left end of the bar is pin supported and can rotates about the pin at Point A. The mass of the bar is m=20kg. The total length of the bar is LAB=3m and LAC=2m. Point A is 0.6 m below the ceiling. A clockwise constant couple moment M= 30Nm is applied on the bar so that the bar rotates from the horizontal position with θ=0° to the vertical position with θ=90°. The spring always maintains at the vertical position. The spring’s stiffness coefficient is k=30N/m and its unstretched length is 0.5 m. The acceleration due to gravity g=9.81 m/s2. During the process that the bar rotates from the horizontal position to the vertical position, determine the following. (2) ) the work done by the couple moment. __________(J) (two decimal places)

A bar is attached to the spring at the point C. The left end of the bar is pin supported and can rotates about the pin at Point A. The mass of the bar is m=20kg. The total length of the bar is LAB=3m and LAC=2m. Point A is 0.6 m below the ceiling. A clockwise constant couple moment M= 30Nm is applied on the bar so that the bar rotates from the horizontal position with θ=0° to the vertical position with θ=90°. The spring always maintains at the vertical position. The spring’s stiffness coefficient is k=30N/m and its unstretched length is 0.5 m. The acceleration due to gravity g=9.81 m/s2. During the process that the bar rotates from the horizontal position to the vertical position, determine the following. (2) ) the work done by the couple moment. __________(J) (two decimal places)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.14P: A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae=...

See similar textbooks

Similar questions

The inclined ladder AB supports a house painter (85 kg) at C and the weight iq = 40 K/m} of the ladder itself. Each ladder rail (t5= 4 mm) is supported by a shoe (ts= 5 mm) that is attached to the ladder rail by a bolt of diameter d = 8 mm
A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae= 304 mm2 for each cable) as shown in the figure. A load P = 20 KN is supported at point D. The crane boom lies in the y-z plane. (a) Find the tension forces in each cable: TAQand TBQ(kN}. Neglect the mass of the cables, but include the mass of the boom in addition to load P. (b) Find the average stress (s) in each cable.
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
Illustrate the free body diagram also
A Pin spanner as shown in Figure, requires moment of 80 Nm to turn the 200 mm diameter shaft about its center O under the action of the applied force P. determine the contact reaction force on the smooth surface at the point A. Engagement of the pin at B may be considered to occur at the periphery of the collar OPTIONS:(MULTI CORRECT(MAY BE)): 1.Reaction at Point A is around 1047 N 2.Value of force P is around 102 N 3.Value of force P is around 133 N 4.Reaction at Point A is around 720 N 5.Reaction at Point A is around 1321 N 6.Value of force P is around 200 N 7.Value of force P is around 213 N 8.Reaction at Point A is around 970 N
A uniform beam of length L = 13.6 meters and mass of 115.1 kg is pinned at one end and is being supported by awire as shown. The wire is connected to the beam x = 4.4 meters from the pin. A person of mass 98.3 kg is standingall the way out on the edge of the beam, the tension in the wire is 4624 N, θ = 16.2 degrees, and φ = 78.9 degrees.If the positive x-axis points to the right, find the horizontal component of the force from the pin on the beam.(in N) a. 1463 b. 2121 c. 3075 d. 4459 e. 6466
The uniform bar AB weighing 240 lb is mounted as shown in the figure upon a carriage weighing 480 lb. The center of gravity of the carriage is at C midway between the wheels. If P = 180 lb and there is no frictional resistance at the wheels, find the value of R1
A beam of mass Mv = 40 kg and length L = 3.0 m is attached to a hinge in the vertical wall. On the bar there is a block, of mass mb = 10 kg, which can be in different positions “x” on the wall. The cable that secures the end of the bar to the upper horizontal slab makes an angle θ = 45o with the bar, that is, with the horizontal (Figure).a) What are the minimum and maximum tensions in the cable as the block moves along the beam?b) If the block is at the center of the beam, what force will the hinge exert?
Three cylinders are piled up in a rectangular channel as shown in the figure. Determine the reactions at the all the points of contact. Cylinder A:Radius=4cm ,m=15kg Cylinder B:Radius=6cm,m=40 Kg Cylinder C: Radius = 5cm,m= 20kg
Find the support reacions and joint force of the construction shown on the figure, if; P=12 kN q=9 kN/m M=12 kN and L=2 m
The 20kg uniform rectangular plate is supported by an ideal pivot at O and a spring which must be compressed prior to being slipped into place at point A. If the modulus of the spring is k=2KN/m, what must be its undeformed length?
nonuniform beam 4.50 m long and weighing 1.40 kNmakes an angle of 25.0° below the horizontal. It is held in position bya frictionless pivot at its upper right end and by a cable 3.00 m fartherdown the beam and perpendicular to it . The center ofgravity of the beam is 2.00 m down the beam from the pivot. Lightingequipment exerts a 5.00 kN downward force on the lower left end ofthe beam. Find the tension T in the cable and the horizontal and verticalcomponents of the force exerted on the beam by the pivot. Start bysketching a free-body diagram of the beam.