The Saw Stop table saw has a special safety breaking mechanism which is able to bring the blade to a complete stop from full speed (4200rpm) if the operator accidentally touches it. The saw is able to do so within 0.001s of the blade making contact with skin.wwwA typical table saw blade has a mass of 700g and a radius of 9cm and can be treated as solid disk,a) What torque is requred to slow the blade in this time?b) Through what angle does the blade turn through as it comes to a stop?

Answered: Image /qna-images/answer/419d39ef-7748-410a-85b0-c16440f1bccb.jpg

The Saw Stop table saw has a special safety breaking mechanism which is able to bring the blade to a comp rpm) if the operator accidentally touches it. The saw is able to do so within 0.001s of the blade making cont A typical table saw blade has a mass of 700g and a radius of 9cm and can be treated as solid disk. a) What torque is requred to slow the blade in this time? b) Through what angle does the blade turn through as it comes to a stop?

The Saw Stop table saw has a special safety breaking mechanism which is able to bring the blade to a comp rpm) if the operator accidentally touches it. The saw is able to do so within 0.001s of the blade making cont A typical table saw blade has a mass of 700g and a radius of 9cm and can be treated as solid disk. a) What torque is requred to slow the blade in this time? b) Through what angle does the blade turn through as it comes to a stop?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a steam engine runs at 150rpm. its turning moment diagram gave the areas in mm2 taken in order above and below the mean torque line is 500,250,270,390,190,340,270,250, the scale for turning moment is 1mm=500mnm, 1mm=5’ if the fluctuation of speed is not to exceed +or-1.5% of mean, determine a suitable diameter and cross-section of the rim of flywheel with axial dimension equal to 1.5times the radial dimension. the hoop stress is limited to 3mpa and the density of material of flywheel is 7500kg/m3.
The kinematic diagram is given as ?12 = 600 and the speed of the mechanism is constant and ?'-12 = 50 rad/second in the slide mechanism, the limb dimensions of which are given below. Find the following items. a) Write the vector closure equations. b) Put the vector closure equations in scalar form. c)Find ?13, ?14. d)Find s'13, ?14. e)Find s'', ?14.
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
Machine Theory Question-1 a) A flywheel is attached to the engine so that the rotational speed of the engine remains between 100 and 110 r/s. If the energy fluctuation is 1.05 KJ here, find the inertia of the flywheel.
pleassssse solve question 9, statics
Plz give proper explanation and derivation. Explain about derivation of shaft strength...?
A merry-go-round with a radius of 2.2m rotates 10.0 times every 5.00s. a. What is the ride’s angular displacement? b. What is the ride’s angular velocity? c. What is the ride's displacement? d. What is the ride's velocity using the angular velocity? e. What is the ride's velocity using the period?
What is the indicated horsepower of a single cylinder four-stroke gasoline engine if the engine speed is 1000 rpm? Assuming the mean effective pressure of 0.55 MPa. The diameter and piston stroke is 110mm and 140mm
A punching machine requires 1600 ft-lb of energy to punch a certain hole. During the punching operation, the speed of the machine is reduced from 180 rpm to 160 rpm. The weight of the arms and hub is considered to be 10 % of the rim weight, and the mean diameter of the flywheel is 32 inches. a) What is the mean or operating rpm of the flywheel? b) Find the coefficient of fluctuation. c) What is the maximum speed of the flywheel, in fps? d) What is the minimum speed of the rim, in fps? d) Determine the weight of the rim, in lb. e) What is the weight of the flywheel, in lb? f) Determine the weight of the arms and hub, in lb.
A drilling machine is capable of drilling 30 holes of 20mm diameter per minute in a 16mm thick steel plate.Theplate has an ultimate shear strentgh as 360 N/mm2. The calculated energy for this process is 2895.2 Nm.Actual drilling process continues during the 36° rotation period of the crank shaft. This crank shaft is driven by a flywheel through a reductionn gear with a ratio of 1:8.In this case the rotation speed is 240 rpm related to the given cycle ratio. Mechanic gain is 80%. Speed fluctuation coefficient is 0.01and flywheel diameter is 0.75m.(a) Find the required power?(b) Find the energy change ΔEk? (c) Find the mass of the flywheel?
1. Calculation for slider crank When, ? = 100 rad/???2 R=62.5mm L=260mm ? = 90 ? = 100 ???/??? Find 1-displacement(x) 2-velocity (v) 3- find acceleration (?)
The max speed for the servo shown is 130RPM when connected to 6V. Assume that the gearbox on your servo is able to output a torque of 1.5 kg-cm while turning at this speed. Using the number of teeth on each gearprovided in the table, determine the torque and rotational speed of the output shaft on the DC motor. HINT: Work backwards from the output shaft and use the equations developed in class that relate the number of teeth to the torque. When working back from the output shaft to gear 7/6, realize that the “torque” transmitted by gear 7 is the SAME as the torque transmitted by gear 6 since they are joined. Then, relate the torque of gear 6 to gear 5 based on their numbers of teeth. Since gears 5 and 4 are actually one piece, the torque in 4 and 5 will be the same (as was the case for gears 6 and 7). Repeat for the other gears, working your way all the way back to the DC motor.