Q1: The cutter bar of a mower is connected to the P.T.O. shaft of a tractor making 1500 stroke per minute. The mower has the following specifications- Length of pitman (L)-85 cm, radius of rotation of crank pin=s Ɛm, S= 20 èm, mass of ms knife=5 kg and mass of crank pin=o.5 kg. If the mass of pitman 4kg has its center of gravity at the distance of 45 cm from the knife end .Calculate: a- The inertia force at each end of the stroke, starting the stroke at oc=0 b-Resulting unbalance forees (Fp) at each end of the stroke. Met mi crak pin positiea for teao Fh Ep

Q1: The cutter bar of a mower is connected to the P.T.O. shaft of a tractor making 1500 stroke per minute. The mower has the following specifications- Length of pitman (L)-85 cm, radius of rotation of crank pin=s Ɛm, S= 20 èm, mass of ms knife=5 kg and mass of crank pin=o.5 kg. If the mass of pitman 4kg has its center of gravity at the distance of 45 cm from the knife end .Calculate: a- The inertia force at each end of the stroke, starting the stroke at oc=0 b-Resulting unbalance forees (Fp) at each end of the stroke. Met mi crak pin positiea for teao Fh Ep

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pulley 1 m in diameter rotating at 300 r.p.m is brought to rest in 80 s. By constant force of friction on its shft. How many revolutions does it moves?
An Olympic lifter (m = 103kg) is holding a lift with a mass of 350 kg. The bar exerts a purely vertical force that is equally distributed between both hands. Each arm has a mass of 9 kg, are 0.8m long and form a 40° angle with the horizontal. The CoM for each arm is 0.5 m from hand. Assuming the lifter is facing us in the diagram below, his right deltoid inserts 14cm from the shoulder at an angle of 13° counter-clockwise from the humerus. Find the force right deltoid
1. A non-uniform is 4.5m long and weighs 640N. It is balance when a 270N weight is hung 0.800m from the light end of the bar and the bar is pivoted at its center. Where is the center of gravity of the bar? 2.Two workers carry a non-uniform beam weighing 730N. The beam is 2.6m long and its center of gravity is 1.1 m from one end. If the workers hold the beam at its end, how much does each worker lift?
A pulley 1 m in diameter rotating at 300 r.p.m is brought to rest in 80s. By constant force of friction on its shaft. How many revolutions does it moves?
For the double slider mechanism shown in the following figure, the crank OA rotates at a uniform speed of 100 rad/s CW. we need to find the required torque for the crank, if two forces act at sliders B and C as shown in the figure. (P = 2KN, Q = 1KN). OA = 30 cm, AB = AC = 100 cm. mB = mC = 1 Kg. Neglect other links weights. The velocity of slip of slider B in m/s2 = Answer 1 Choose... The velocity of slip of slider C in m/s2 = Answer 2 Choose... The acceleration of slip of slider B in m/s2 = Answer 3 Choose... The acceleration of slip of slider C in m/s2 = Answer 4 Choose... The magnitude of required torque for the crank in N.m = Answer 5 Choose...
A mono-cylinder engine has r = 0.3 m, l = 0.9 m, It has: crank mass m2 = 4.5 kg , crank rG2 = 0.4r, conrod mass m3 = 12 kg ,conrod rG3 = 0.3l from A, and piston m4 = 5 kg. The crank is rotating at constant speed ω =3000 rpm. The following equation is an approximation of the gas force over 180° of crank angle with Fgmax = 3000 N and β = 15º. we need to find the gas force, gas torque, and inertia force . Use approximate expressions in your calculation
URGENT.THEORY OF MACHINE A circular cutter has 4 different-sized blades, Blade A, Blade B, Blade C and Blade D, are rotating at constant velocity of 230 rad/s.The known parameters for each blade are : The weights: WA = 15 kg, WB = 25 kg, WD = 20kg The radius: RA = 300 mm, RC = 200 mm and RD = 350 mm The angle: θA = 190°; θB = 45°; θC = 90°; θD = 260° You have been asked to determine: (a) The weight of Blade C (in N) and radius of Blade B (in m) to make the whole cutter system balanced, without adding additional blade. (b) If the plane containing B and C is 0.5 m apart, determine position of planes A and D. Note: If plane A as baseline, find the length for each plane to the baseline (lb, lc, ld) (c) Sketch and label the statically balanced link of the system.
Consider a disc of mass, M with radius 0.5 m on a slope with angle 45 degrees to the horizontal. It has a good grip on the slope and does not slip. The disc is constructed so that its mass per unit area, ρ(r) = r1/2 kg m−2, with r being the radial distance in metres from the axis of the disc. What is the equation describing the linear acceleration of the centre of mass of the disc down the slope in terms of the angular acceleration of the disc.
Car mass = 1,50 kg Spring body =1,30,000 W/m Spring wheel= 1,000,000 A/m Solve and get its transfer function with fbd. Ty
A 70 kg human steps at a springboard causing it to deflect at a value of 2 centimeters. What is the spring constant in kN/m of the springboard as a cantilever model?
During a bicep curl on a bicep curl machine, I'm curling a weight stack of 100 pounds (single arm...I'm jacked like that). At this very moment, the weight stack has a moment arm of 0.12m, my elbow has an angle of 63deg, my muscle force vector has an angle of 23deg, and it attaches 3cm below my elbow joint on my radius. How much force must my bicep create right at this moment to hold the weight stack in place?
In the crank-connecting rod mechanism shown in the figure, the crank rotates with a constant angular velocity (the system operates in the horizontal plane and friction will be neglected). T12 torque for the 10% displacement of the piston at the expansion time,a) Gas force P (piston diameter is 60 mm).b) mass m4Calculate for.(r=10 cm; l=30 cm; AG3=10 cm ; m3=4 kg, m4=3 kg, N=2000 rpm)