The shaft is supported by smooth journal bearings at A and B that only exert vertical reactions on the shaft. (Figure 1) Part A If d = 98 mm , determine the absolute maximum bending stress in the beam. Express your answer to three significant figures and include the appropriate units. HẢ ? Figure < 1 of 1 > Value Units Omar = Submit Request Answer 12 kN/m Provide Feedback B_ 3 m 1.5 m

The shaft is supported by smooth journal bearings at A and B that only exert vertical reactions on the shaft. (Figure 1) Part A If d = 98 mm , determine the absolute maximum bending stress in the beam. Express your answer to three significant figures and include the appropriate units. HẢ ? Figure < 1 of 1 > Value Units Omar = Submit Request Answer 12 kN/m Provide Feedback B_ 3 m 1.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 107 MPa, determine the minimum diameter (in mm rounded to the nearest hundredths) required for rod 2. Assume P = 80 kN and Q = 140 kN.
For the shaft shown, a. Determine the maximum stress on the shaft and the maximum angle of twist of end D relative to end A. b. If the stress in every section must not exceed 25 MPa, what should be the uniform diameter of the shaft? dAB = 100mm, dbc = 80mm, dcd = 50mm G for the shaft is 80GPa. Consider clockwise torques as negative.
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28MPa, fy is 420MPa and Wu is 89.9kN/m. 1. what is the ultimate moment capacity of the beam? 2. what is the height of the equivalent stress block? 3. Determine the number of bars required for this beam
The steel shaft with two different diameters rotates at 4.2 Hz. The power supplied to gear C is 68 kW, of which 42 kW is removed by gear B. Find the maximum shear stress (in Pa) in the shaft if d = 58.1 mm, h = 60.6 mm, L = 3.9 m, M = 2.1 m, and G = 83.49 Gpa. Round off the final answer to two decimal places
Two steel [E=29,600 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 6.500 in, and a wall thickness of 0.257 in. Pipe (2) has an outside diameter of 4.250 in. and a wall thickness of 0.215 in. Assume L_{1} = 13ft and L_{2} = 18fi . If the normal stress in each steel pipe must be limited to 23 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a).
A transmission tower shown below is subjected to lateral loads as shown. A =2.3 kN, B =5.2 kN, C =7.7 kN Determine the magnitude of the axial force in member DH (in kN).
Step 2 1st condition Bending moment at hinge D =0 Rc*2 = (3*2)*(2/2) Rc = 3 KN Rc = 3 KN (upward) could you explain where these numbers coming? Why that divided by two? and is formula like this: 3kN/m*2m*2m/2m? 2nd condition Bending moment at hinge F =0 RB*2= (3*4)*(3+4/2)-3*7 RB = 19.5 KN RB = 19.5 KN ( upward) Same this formula If you can explain this like drawing this on paper and write where all meters and number come, that would be help me. If you could also tell the direction, where you would calculation them
The column is constructed from high-strength concrete and A-36 steel reinforcing rods. If it is subjected to an axial force of 30 kips, determine the average normal stress in each rod (ksi). Each rod has a diameter of 0.58 inch. Esteel = 29 x 103 psi and Econcrete = 4.2 x 103 psi, r = 4 inches
An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The butt diameter is 450 mm and the tip diameter (the top of the pole) is 320 mm. The weight of the pole, cross arms, and wires is 33 kN. Assuming the pole transmits the load as a point load, find the change in vertical stress in kPa at 2 m depth. a. 17.8 b.393.9 c.63.0 d.3.9
A solid constant-diameter circular shaft is subjected to the torques of TA = 470 Ib-ft, Te = 1090 lb ft, Tc = 840 Ib-ft, and Tp = 220 lb ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6. (b) If the allowable shear stress in the shaft is 5200 psi, what is the minimum acceptable diameter for the shaft?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends. If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (lb∙in) that may be applied at section C? pls write legibly thanks
Two steel [E = 29,800 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.750 in. and a wall thickness of 0.278 in. Pipe (2) has an outside diameter of 3.750 in. and a wall thickness of 0.209 in. Assume L= 10 ft and L›= 15 ft. If the normal stress in each steel pipe must be limited to 15 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a).