The shaft rotating at 120 rpm carries a spur gear A having 80 teeth with a diametral pitch of 5. The teeth are of the 20°, full-depth, involute form. The gear receives 40 hp from a pinion to the right as shown. Each sprocket delivers 20 hp to mating sprockets to the left. Compute the torque delivered to the shaft and the tangential and radial forces exerted on the shaft by the gear. TB = 21000 in-lb, TB = 10500 in-lb W₁ = 2625 lb, W, = 955.42 lb 16-in spur gear 20°FD P drives A 14-in chain sprockets (C and D) Chain Chain

The shaft rotating at 120 rpm carries a spur gear A having 80 teeth with a diametral pitch of 5. The teeth are of the 20°, full-depth, involute form. The gear receives 40 hp from a pinion to the right as shown. Each sprocket delivers 20 hp to mating sprockets to the left. Compute the torque delivered to the shaft and the tangential and radial forces exerted on the shaft by the gear. TB = 21000 in-lb, TB = 10500 in-lb W₁ = 2625 lb, W, = 955.42 lb 16-in spur gear 20°FD P drives A 14-in chain sprockets (C and D) Chain Chain

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A similar pair of helical gears , also on parallel axes, are to have involute teeth, of 20o normal pressure angle, and 3 mm normal module. The wheels are to have 26 and 34 teeth, and to work with a centre distance of 146 mm. Calculate the transverse pressure angle in degrees.
A chain with speed of 900 fpm has driving sprocket turns at 1000 rpm. If the pitch of chain is 3/4-in, find the number of teeth of driving sprocket. (Ans. 14 teeth)
8. If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0 to 1500 rpm in 3 seconds. Calculate the heat generated for each engagement if clutch starting torque is 10 in-lb.
Two parallel shafts have an angular velocity ratio of 4 to 1 are connected by gears, the largest of which has 40 teeth. Find the number of teeth of smaller gear.
A Coniflex, straight-tooth bevel gearset is supported on shafts with centerlines intersecting at a 90° angle. The gear is straddle mounted between closely positioned bearings, and the pinion overhangs its support bearing. The 15-tooth pinion rotates at 900 rpm, driving the 60-tooth gear, which has a di- ametral pitch of 6, pressure angle of 20°, and face width of 1.25 inches. The material for both gears is through-hardened Grade I steel with a hardness of BHN 300 (see Figure). It is desired to have a reliability of 90 percent, a design life of 10° cy- cles, and a governing safety factor of 2.5. Estimate the maximum horsepower that can be transmitted by this gear re- ducer while meeting all of the design specifications given.
ANSWER ASAP The worm gear rotating at 1250 rpm drives a worm wheel and whose velocity ratio is 12 to 1. A driving motor with 12 hp is used to supply the worm with worm pitch gear diameter of 3.5 in. Find the tangential force on the gear.
Two cqual involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angleare in mesh. Determine the minimum addendum if 2 pairs of teeth are always in mesh.The gear wheels rotate at 750 r.p.m. and transmit 4.6 kW. Find the normal force at eachpair assuming equal direction of load between the pairs. Neglect friction.
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 ifits gearbox 5th gear is selected. The gear’s teeth are of involute form with amodule of 8 mm, an addendum is double the module, and the pressure angle isequal to 20° .1.1. If the driving shaft of the front wheels of the truck is connected to the output shaftof the gearbox, determine the number of teeth on the pinion to avoid interferenceand the corresponding number of teeth on the gear wheel.
A pair of gears, having 40 and 30 teeth respectively, are of 25° involute form. Theaddendum length is 5 mm and the module is 5.5 mm. If smaller wheel is the driver androtates at 1500 r.p.m. find the velocity of sliding at the point of engagement and at thepoint of disengagement.
2. A shaft is supported on bearings A and B, 800 mm between centres. A 20 degrees straight tooth spur gear having 600 mm pitch diameter, is located 200 mm to the right of the left hand bearing A, and a 700 mm diameter pulley is mounted 250 mm towards the left of bearing B. The gear is driven by a pinion with a downward tangential force while the pulley drives a horizontal belt having 180 degrees angle of wrap. The pulley also serves as a flywheel and weighs 2000 N. The maximum belt tension is 3000 N and the tension ratio is 3: 1. Determine the maximum bending moment and the necessary shaft diameter if the allowable shear stress of the material is 40 MPa.
The pitch circle diameter of the smaller of the two spur wheels which mesh externally and haveinvolute teeth is 100 mm. The number of teeth are 16 and 32. The pressure angle is 20° and theaddendum is 0.32 of the circular pitch. Find the length of the path of contact of the pair of teeth.
A synchronous belt drive system is used as a speed reducer. The input shaft rotates at 1000 rpm and has a 36-tooth sprocket with a pitch diameter of 3.609 in. The output shaft has a 72-tooth sprocket with a pitch diameter of 7.218 in. the center distance between the two shafts is 15.01 in. Determine the following for the belt drive: a. The velocity ratiob. The angular velocity of the output shaftc. The linear belt speedd. The belt wrap on the input and output sprocketse. The belt perimeter lengthf. Draw the schematic of the belt drive system