The simple connecting rod mechanism shown in Figure Q12 has a connecting rod length AB of 142mm and a crank radius OA of 46mm. The connecting rod has a centre of gravity C, which is located 32mm from end A. When the crank angle 0 is 305° and the crankshaft speed (w) is 6500rpm clockwise as shown, determine by kinematic analysis: The magnitude and direction of the angular velocity of the connecting rod. The magnitude and direction of the velocity of the piston. The magnitude and direction of the angular acceleration of the connecting rod. The magnitude and direction of the acceleration of the piston. The magnitude of the acceleration of the centre of gravity (C) in the X and Y directions.

The simple connecting rod mechanism shown in Figure Q12 has a connecting rod length AB of 142mm and a crank radius OA of 46mm. The connecting rod has a centre of gravity C, which is located 32mm from end A. When the crank angle 0 is 305° and the crankshaft speed (w) is 6500rpm clockwise as shown, determine by kinematic analysis: The magnitude and direction of the angular velocity of the connecting rod. The magnitude and direction of the velocity of the piston. The magnitude and direction of the angular acceleration of the connecting rod. The magnitude and direction of the acceleration of the piston. The magnitude of the acceleration of the centre of gravity (C) in the X and Y directions.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

: A machine operator has to perform 3 operations, Turning, Threading & Knurling on three machines A, B & C in the order ABC. Find the optimum sequences when the time in hours is given. Job Turning Ai Threading Bi Knurling Ci 1 3 8 13 2 12 6 14 3 5 4 9 4 2 6 12 5 9 3 8 6 11 1 13
The title of our study is "Design and Fabrication of an Agricultural Spraying Attachment for an Autonomous Rover" we need help in the machine design part of our study, specifically Pump selection, battery selection, and center of gravity computation I already sent you the image of the rover Rover weight capacity 35 kilo grams (payload) Rover measurements: Wheel distance - 14.5 inches and 8.5 inches Rover platform size (width & length) 14.4 inches x 10.4 inches Height- 15.8 inches. Water tank selection More or less 25 liters *For tank selection we need to justify the size with the center of gravity, proving that is the maximum dimension or liters of the tank because the center of gravity will be higher making the rover prone to toppling Pump selection *Our sprayer design has two nozzles which splits using a tee splitter, we need to find the size of the pump to obtain the same discharge rate of a normal sprayer. A normal sprayer has a 12V pump and a pressure from 0.2 to 0.45 mpa…
Solve the last highlight by red pen experession only In which they said to draw a graph
The analyst in the Dorben Company wishes to assign a number of like facilities to an operator based on minimizing the cost per unit of output. A detailed study of the facilities revealed the following: Loading machine standard time = 0.30 minutes Unloading machine standard time = 0.25 minutes Walk time between two machines = 0.09 minutes Operator rate = $12.00 per hour Machine rate (both idle and working) = $18.00 per hour Machine cycle time = 1.55 minutes TEC = The Expected Cost a) With your initial estimation, how many machines can be serviced exactly?(please keep a non-integer with three decimal places) b) How much is your TEC per piece if the operator has idle time? (please keep three decimal places) c)How much is your TEC per piece if the machine has idle time? (please keep three decimal places) d) How many of these machines should be assigned to each operator?(please write down a numerical number)
An assembly line is to be designed to operate 71⁄2 hours per day and supply a steady demandof 300 units per day. Here are the tasks and their performance times: Performance Performance Preceding Time Preceding Time Task Tasks (Seconds) task Tasks (Seconds) a — 70 g d 60 b — 40 h e 50 c — 45 i f 15 d…
The following four jobs must be processed through a three-machine flow shop.MachineJob A B C1 4 262 2 373 6 564 3 48Find the optimal sequencing of the jobs in order to minimize the makespan.What is the makespan at the optimal solution? Draw a Gantt chart illustrating yoursolution.
where did you get value of Ws, the 572.116, the 0.9608, and 0.3350? you just copied the entire solution from internet
You have been asked to work on some design problems and technically support the team working on material removal processes: 1. Technician is turning (lathing) a work material with a shear strength of 270 MPa as shown in Figure 1. The following conditions are used: v = 5.0 m/s, f = 0.30 mm/rev, d = 3.0 mm, and rake angle = 15° in the direction of the chip flow. The resulting chip ratio = 0.5. Chip Tool R. RF. Work Figure 1: Turning process. Using the orthogonal model as an approximation of turning, you have been asked to determine: (a) Shear force. (b) Cutting force and thrust force. (c) Friction angle.* ) material removal rate = 4500 mm3/min * ) shear plane angle = 29.02° * ) shear strain = 2.052
Activity Immediate Predecessor(s) Te VAR Slack A - 5 0.444 0 B - 2 0.111 4 C - 3 0.444 6.5 D A 7.5 0.25 0 E B 6.5 0.694 4 F C 8 0.111 6.5 G D, E 5 0.111 0 What is the critical path for the project described by this table? A. C-F B. B-E-G C. A-D-G D. A-B-C Click to select your answer.
1. A certain batch of parts is routed through six machines in a batch production plant. The setup and operation times for each machine are given in the table below. Batch size is 200 and the average nonoperation time per machine is15 hr. Determine (a) manufacturing lead time and (b) hourly production rate for operation 4.Machine 1 2 3 4 5 6Setup time (hr) 5 3 6 4 5 3Operation time (min) 3.0 3.3 8.2 3.9 4.5 2.3 a. 6(4.3+200(3.9/60)+15) = 193.8 hours 24.2 days if 8 hour shiftb. 4(60)+200(3.9)/200 =5.1 hourly production for operation 4 2. Suppose the part in the previous problem is made in very large quantities on a production line in which an automated work handling system is used to transfer parts between machines. Transfer time between stations is 30 sec. total time required to setup the entire line is 102 hr. Assume that the operation times at the individual machines remain the same as in the previous problem, Determine (a) manufacturing lead time for a part coming off the line,…
Dear sir/madam pls give me ans for this calculation thanks
Please look at the Units. don't make mistake. (Provide only handwritten solution,Previous solver skip it)