350mmi The simply supported beam has an l-shaped cross section. (1) Determine the values and locations of the maximum tensile and compressive bending stresses. (2) Sketch the bending stress distribution over the cross section on which the maximum bending stress occurs. No credits if free body diagram is not present. O 35m 8 kN/m 100 kN 11mm 7.5mm- 11mm 0.8 m 14 1.m 175mm |100KN

350mmi The simply supported beam has an l-shaped cross section. (1) Determine the values and locations of the maximum tensile and compressive bending stresses. (2) Sketch the bending stress distribution over the cross section on which the maximum bending stress occurs. No credits if free body diagram is not present. O 35m 8 kN/m 100 kN 11mm 7.5mm- 11mm 0.8 m 14 1.m 175mm |100KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

QUESTION-1: Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
4. An aerial copper wire (E =1x 10 5 N/mm ^2) 40 m long has cross sectional area of80 mm2 and weighs 0.6 N per meter run. If the wire is suspended vertically, calculatethe maximum weight which this wire can support at its lower end if the limiting valueof stress is 65 N/mm 2.a. 4627 Nb. 4281 NC. 4519 Nd. 5188 N
A circular beam carries a concentrated and a distributed load as shown in the figure. Determine the following unknowns if the modulus of elasticity is 90GPa and the maximum shear is 444.9kN. Let, P=170kN, a=2.5m, b=1m and c=3m ; If the deflection at the free end (leftmost part of the beam) is equal to -14.183444485219mm, Determine the radius of the cross-section of the circular beam. Determine the slope at the free end of the beam
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
Given the following data:Cross section: 50mm x 75mmP = 200 kNθ = 15 ° with the x-axis Find the shear stress (in MPa) on plane A-A.
Analyze the given semi-frame and Develop the required equation/solution for every given answer. 1. What is the shear at E? 2. What is the shear and moment at point C? 3. What is the shear and moment at point A? please provide a solution, thank u so much.Given: Shear and moment at left of C Vc= -4.5 kn Mc= -4.5 kn-m Shear and moment at right of C Vc= 37.5 knMc= -94.5 kn-m
Draw the shear force and bending moment diagram of the beam. Draw the distribution of normal stress and shear stress in the cross section of the beam at the B support. q=12t/m b=85mm h= 750mm t=30mm
Using virtual work method, find: (a) the real internal force F in member BF in kN (b) real internal force F in member GH in kN (c) virtual internal force Fv in member HG due to a one unit horizontal load applied at joint G (d) virtual internal force Fv in member CD due to a one unit horizontal load applied at joint G (e) horizontal displacement at joint G due to the applied loads in mm. Given: a=25kN b=22kN c=4km
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x150 mm section and E = 80 GPa. Show complete and organized solution. a. Vertical Reaction at B in kN. b.Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. Given: a- 7m b- 24kN/m C- 30kN
Given: Signage subjecting 1.606 kPa pressure. Signage = 2.404 m x 1.01 m Offset of signage from pole center = 0.404 m Signage center distance from the ground = 8 m 1. Determine max shear force at the base of pole in kN. 2. Determine max moment at the base of pole in kN-m. 3. Determine max torque at the base of pole in kN-m.
Write legibly and box the final answer. Determine the maximum mass (kg) that can be lifted at E if the 11.670-HP motor A has a maximum rotation speed of 301.20 rpm where the diameter of the shaft AB and CE are 10.237 mm and 15.402 mm, respectively. The allowable shearing stress is 1.001 GPa with F.S. of 1.76 for both shafts. Neglect the deformation of the cable at E. Where: radius of the gear at B, rB = 113.10 mm radius of the gear at C, rc = 158.58 mm
Compute the critical buckling load and the critical buckling stress of W18x71 with a length of 30ft .