The slotted guides in the figure act according to the relations x = 16 - 12t + 4t ^ 2 and y = 2 + 15t - 3t ^ 2. Here x and y are in millimeters and t is in seconds. Find the tangential and normal component of the acceleration of the pin "P" and its directions at time t = 2 s

The slotted guides in the figure act according to the relations x = 16 - 12t + 4t ^ 2 and y = 2 + 15t - 3t ^ 2. Here x and y are in millimeters and t is in seconds. Find the tangential and normal component of the acceleration of the pin "P" and its directions at time t = 2 s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tire 0.400 m in radius rotates at a constant rate of 170 rev/min. Find the speed of a small stone lodged in the tread of the tire (on its outer edge). (Hint: In one revolution, the stone travels a distance equal to the circumference of its path, 2?r.)____m/sWhat is the acceleration of the stone?_____m/s2 away from the center of the path? tangent to the path? toward the center of the path?
Example] The two ends of bar AB slides along the vertical and horizontal surfaces. MA = 1,, MB = 1,0 = ot(@= const.) Determine the motion equation, the magnitude of the velocity and acceleration for point M. B
QUESTION 7 PLS 6) A ball is thrown vertically upward from the surface of the earth with an initial velocity of 30 m/s. Two seconds later a second ball is thrown upward from the same point with a velocity of 24 m/s. Derive an expression for the relative position, velocity, and acceleration of ball 1 with-respect-to ball 2 for time t≥2sec. (neglect air resistance and assume acceleration of gravity is 9.81 m/s2. 7) For the two balls thrown in problem 6, how far above the earth will the two balls meet (i.e. what is their height when they pass each other)?
A stroke of a reciprocating engine is 600 mm. neglecting the effect of angularity of the connecting rod, find a) velocity in m/s of the piston , b) acceleration of the piston in m/s^2 when the crank is 30 degree past TDC. The engine is running at 720 rev/min tools : r=1/2 stroke, v=wrsin theta! a=wr^2costheta
..A crane is to raise a load of 25,000 N at an acceleration of 1 m/s2 through a 6 x 19 wire rope whose weight is 15,000 N. The diameter of the rope is 32 mm and the rope drum diameter is 960 mm. Take the Young’s modulus for the wire rope as 80 kN/mm2. Assume dw = 0.063 d. Which of the following is the bending load of the wire rope? Group of answer choices 61 kN 40 kN 4 kN 80 kN
In a physics lab experiment, you release a small steelball at various heights above the ground and measure the ball’s speedjust before it strikes the ground. You plot your data on a graph that hasthe release height (in meters) on the vertical axis and the square of thefinal speed (in m2/s2) on the horizontal axis. In this graph your datapoints lie close to a straight line. (a) Using g = 9.80 m/s2 and ignoringthe effect of air resistance, what is the numerical value of the slope ofthis straight line? (Include the correct units.) The presence of air resistancereduces the magnitude of the downward acceleration, and the effectof air resistance increases as the speed of the object increases. Yourepeat the experiment, but this time with a tennis ball as the object beingdropped. Air resistance now has a noticeable effect on the data. (b) Isthe final speed for a given release height higher than, lower than, or thesame as when you ignored air resistance? (c) Is the graph of the releaseheight…
A circular saw blade 0.6 m in diameter starts from rest and accelerates with constant acceleration to an angular velocity of 100 rad.s-1 in 20 s. Find the linear velocity of a point in the rim of the saw when the angular velocity is 10 rad.s-1.
The 100 meter diameter wheel needs to be designed so that it rotates at a constant rate and every complete revolution takes 15 minutes. The wheel has been installed in a vertical plane and the lowest seat is 2m above the ground surface. Each ride consists of only one full rotation. Find a further general expression for the horizontal displacement of the rider from its initial position with respect to both time and angle of rotation and hence determine the speed of the rider when t= 180 sec. Using calculus, determine what the maximum horizontal and vertical speeds of the rider would be and at which points during the ride they occur. State expressions for the acceleration of the rider in both horizontal and vertical directions and show that the resultant acceleration experienced by the rider is independent of where on the ride he/she might be. In designing a new wheel with the same diameter and same ride duration as before it is proposed that the wheel’s angular speed should not…
An airplane starts from rest at t=0. During a curvilinear flight path, airplane’s acceleration in cartesian components is defined by ax= 0.46t + 0.2 m/s2 and ay= 0.6t m/s2. At t = 4 sec, Given the mass of aircraft is 1500 kg, calculate a) Normal and tangential forces
Please include explanation. A 6-MW offshore wind turbine has a capacity factor of 40%. It has a height of 120 m, and 107-m long blades. The angular acceleration is 1.388 rad/s2. Assume that the distance from the center of the turbine to the connection with the blade is negligible, and that the turbine starts from rest. At ? = 12 s, calculate the velocity and the acceleration for points (a) at half the length and (b) at the tip of the blade.
You are driving South on I-29. You realize that you are late for an appointment and speed up. With angular velocity and angular acceleration, respectively, which of the following statements is necessarily correct about the period of acceleration? A). For all wheels of your car, velocity points East and acceleration points West. B). For the right front wheel, both velocity and acceleration point East. C). For the left rear wheel, both velocity and acceleration point South D). For the left rear wheel, both velocity and acceleration point West.
A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and accelerates uniformly to omega = 24 rpm in t= 10 sec and maintain then maintain this constant 24 rpm speed. The dimensions are rA= 1 in, rB= 9 in and rC=16 in. 2) After 10 sec, find the distance s2 in feet and in NC es needed to reach the 11 ft, find thetaC2(t), alphaA2, alphaB2 in rad/s^2, omegaA2(t), omegaB2(t) in rad/s, thetaA2(t), in rad and the distance s2 in ft that should be made to get to the 11 ft raising distance of the load. 3) Deduce the number of revolutions made by gear A and how long it will take, to raise the load up to 11 ft.