The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. www A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. www www wwwwwww www w m w www w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW d A D B E

The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. www A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. www www wwwwwww www w m w www w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW d A D B E

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Bearing stress 5. Please provide proper discussion and illustration also complete solution and clear solution please thank you A solid shaft is designed to transmit 50kN @ 1800 rpm to a gear by means of 156 mm long key with square cross-section. The shaft diameter is 35.6mm. What should the cross-section be in mm2 to resist shearing, if the allowable shear stress on the key is 20 MPa?
This engine is used in a hoist. Motor 2.5 kWwith the help of gears with a power of and n = 500 rpm.transmits. If the shear strength of the AB shaft is τa = 160 MPa;a) Find the diameter of AB shaft with 1.4 times safety.b) Find the maximum force F the engine can carry.
Two spur gears transmit 36kW with a velocity ratio of 2:1. The speed of the smaller driving gear is 100rpm. The centre distance between the shafts is to be as near as possible to 920mm. If m=10 and all-21MPa, determine a) Diameter of the shafts b)PCD for each wheel c)Number of teeth on each wheel d) Actual centre distance [ e) Width of the teeth
. Determine the angle of twist for the steel (AISI 4340, OQT 1200 F) hollow shaft with anoutside diameter of 40 mm and an inside diameter of 30 mm when transmitting 28 kWof power at a speed of 45 rad/sec. The shaft length is 400 mm
The solid steel shaft is supported by frictionless bearings in D and E. This system is connected to a motor that provides 5 kW of power to the shaft while rotating at w = 75 rpm. If A and B gears get 2 kW and 3 kW respectively, determine the minimum shaft diameter. w rotation speed and safety shear stress τem = 35MPa are known and given in the table with your names below.
The splined ends and gears attached to the steel shaft are subjected to the torques shown in Figure 4. Take G = 75 GN/m². (i) (ii) Determine the location along the 40 mm diameter shaft where the shear stress is largest and plot the variation in shear stress from the shaft centre to its outer surface. Determine the angle of twist of sections C, D, and B relative to end A by producing a graphical plot of the variation of angle of twist from end A to end B (wind-up diagram). 300 N-m 500 N-m A www. 300 mm 200 N.m MAAN 400 mm Figure 4 500 mm 400 N-m
A short stub shaft, made of SAE 1035, as rolled, receivers 30 hp at 300 rpm via a 12-in. spur gear, the power being delivered to another shaft through a flexible coupling. The gear is keyed (profile keyway) midway between the bearings. The pressure angle of the gear teeth   20o, N = 1.5 based on the octahedral shear stress theory with varying stresses. (a) Neglecting the radial component R of the tooth load W , determine the shaft diameter. (b) Considering both the tangential and the radial components, compute the shaft diameters. (c) Is the difference in the results of the parts (a) and (b) enough to change your choice of the shaft size?
A drive shaft running at 2500 rpm has outer diameter of 80mm and innerdiameter of 60mm. The allowable shear stress in the shaft is 40MPa. Determine themaximum power that can be applied.
an aluminum shaft is 6ft. and has toruq of 500 lb-ft. the shear stress is 6500 psi and the angle of twist must not go over 3 1/2 degrees in the 6ft. pick the economical shaft size.
A shaft in torsion only is to transmit 2500 hp at 570 rpm. Its material’s allowable shear stress is 10 ksi. (a) What should be the diameter of a solid shaft? (b) If the shaft is hollow, Do = 2Di, what size is required? (c) Which is the lighter? By what percentage? (d) Which shaft is the more rigid? PLEASE I NEED IT ASAP . THANK YOU
A 1.5-inch Monel shaft is used in a torsional application. Based on the operating speed of 100 rpm and factor of safety of 12. How much horsepower can it transmit? Assume the shearing stress is ¾ of the ultimate tensile stress which is 100 ksi.