I need the answer as soon as possible 29. The blade and fluid velocities for an axial turbine areas shown in the figure.Blade speed150 m/s300 m's150 m/sA.65°EntryExitThe magnitude of absolute velocity at entry is 300 m/s atan angle of 65° to the axial direction, while themagnitude of the absolute velocity at exit is 150 m/s. Theexit velocity vector has a component in the downwarddirection. Given that the axial (horizontal) velocity is thasame at entry and exit, the specific work (in kJ/kg) is

Given; The blade and fluid velocities for an axial turbine are given if fig. Therefore the data is…

Answered: the specific work

Engineering

Mechanical Engineering

the specific work

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider an inward flow reaction turbine in which velocity of flow at inlet is 3.8m/s. The 1m diameter wheel rotates at 240rpm and absolute velocity makes an angle of 16° with wheel tangent. Determine (1) velocity of whirl at inlet, (2) absolute velocity of water at inlet, (3) vane angle at inlet, and (4) relative velocity of water at entrance. Show the schematic diagram and complete solution with units.
An inward flow reaction turbine has external and internal diameters as 1.095 m and 0.553 m respectively. The turbine is running at 210 R. P. M. The velocity of flow through the runner remains constant and is equal to 2.0 m/s. The width of the turbine at inlet is 241 mm. The guide blades make an angle of 10.5oto the tangent of the wheel. If the discharge of the turbine at the outlet is radial determine the following:i) Draw the inlet and outlet velocity diagramsii) The absolute velocity of the water at the inlet of the runner.iii) The velocity of whirl at inletiv) The relative velocity at inletv) The runner blade anglesvi) Width of the runner at outletvii)The hydraulic efficiency of the turbine
Q4(b) A water turbine model is constructed at ratio of 1:8 with power system of 10 kW at speed of 555 rpm under a head of 2.5 m. Overall efficiency for both model and prototype is assumed at 0.93. (i) Determine the specific speed. (ii) If the prototype is run under a head of 25 m, calculate its rotational speed, power and discharge.
A turbine develops 144 HP running at 100 rpm under a head of 7.7 meters. (a)At what speed, in RPM, should the turbine run under a head of 11 meters? (b)What horsepower would be developed?
At a hydraulic plant the propeller type turbine are rated at 48,000 HP at 82 rpm under a 14 meters head, the diameter is 7 meters, for a geometrical similar turbine to develop 36,000 HP under a 11 meters head. After resolving the percentage change in probable flow, determine the following: (A) What diameter, in meter, of the impeller to be used? (B) What is the speed, in RPM, should be used?
Pls show detailed solution Example 2.2A typical industrial-scale wind turbine has a peak efficiency of about 0.44 for a wind speed of 9 m·s−1. That is, it converts about 44% of the kinetic energy of the wind approaching it into usable electrical energy. The total air flow impinging on such a turbine with a rotor diameter of 43 m is about 15,000 kg·s−1 for the given wind speed. a) How much electrical energy is produced when 1 kg of air passes through the turbine?(b) What is the power output of the turbine?(c) If there is no heat transferred to the air, and if its temperature remains unchanged, what is its change in speed upon passing through the turbine?
The axial flow pump produces a discharge of 0.095 m3/sm3/s. (Figure 1) The impeller is rotating at ω� = 80 rad/srad/s, and it has a mean radius of 75 mmmm. The diameter of the impeller's shaft is 100 mmmm. Determine the angle α2�2, which the velocity of the water as it exits the blades V2�2 makes with its tangential component Vt2��2. Express your answer using three significant figures.
Note: Don't copy from other experts solution. Read the question carefully and give me right solution with clear calculations. The absolute velocity of a jet of steam impinging on the blades of a steam turbine is 2,200 ft/sec, and that leaving is 980 ft/sec. Assume α1 = 10°, α2 = 155° , u1 = 36 ft/sec, u2 = 72 ft/sec, and r1 =4-inches, r2 = 8-inches. Knowing that the density times flow rate, ρQ = 0.0122 slugs/sec, what is the Power delivered, in HP?
[5] A Francis turbine operates at its maximum efficiency point at h0 = 0.94, corresponding to a power specific speed of 0.9 rad. The effective head across the turbine is 160 m and the speed required for electrical generation is 750 rev/min. The runner tip speed is 0.7 times the spouting velocity, the absolute flow angle at runner entry is 70 deg from the radial direction and the absolute flow at runner exit is without swirl. Assuming there are no losses in the guide vanes and the mechanical efficiency is 100%, determine (i) the turbine power and the volume flow rate; (ii) the runner diameter; (iii) the magnitude of the tangential component of the absolute velocity at runner inlet; (iv) the axial length of the runner vanes at inlet.
A centrifugal pump delivers 25 liters of water per second against a head of 10 meters and running at 1300 rpm requires 10 kW of power. Determine the discharge, head of the pump and power required if the pump runs at 1500 rpm. (Ans. 0.0288cumec or 1.73 cu.m./min , 13.31m, 15.36kw)
The axial flow pump produces a discharge of 0.095 m3/sm3/s. The impeller is rotating at ωω = 110 rad/srad/s, and it has a mean radius of 75 mmmm. (Figure 1) Figure 1 of 1 Part A Determine the magnitude of the velocity of the water as it exits the blades. Express your answer to three significant figures and include the appropriate units. V2V2 = nothingnothing SubmitRequest Answer Part B Complete previous part(s) Part C Determine the magnitude of the relative velocity of the water as it flows off the blades of the impeller. Express your answer to three significant figures and include the appropriate units. (Vrel)2(Vrel)2 = 4.27ms
While rotating at 900 rpm, a centrifugal pump delivers 2500 gpm of water at ahead of 75 ft. If the impeller diameter is 1.5 ft. and the blade width is 1.75 in.,find the (a) blade angle β2, (b) radial velocity Vr2, and (c) blade speed u2. Assumeno whirl at the inlet.Ans: β2=12.5°; Vr2=8.1 ft./s; u2=70.7 ft./s