I attached the question finiAn oil of viscosity 5 poiseis used for lubricationbetween a shaft andsleeve. The diameter ofthe shaft is 0.5 m and itrotates at 200 rpm.Calculate the kW powerlost in the oil for a sleevelength of 100 mm. Thethickness of the oil film is1.0mm.O a. 4.76Ob. 8.45c. 8.42

Given Data Film thickness is: y=1 mm=1×10-3 m The diameter of the shaft is: d=0.5 m The speed of…

Answered: I attached the question

Engineering

Mechanical Engineering

I attached the question

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I've been struggling about this problem. How can I get the fluid velocity from the Reynolds numbers. That is the required value for Re. If, the given values are Water Density = 10000 kg/m3, Diameter of tube = 0.05m and Dynamic Viscosity = 0.001 Pa-s. If the formula is Re = Vρd/μ.
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 m²/s and SG-0.9. A. Find the frictional resistance exerted by the oil on the shaft in Newtons (N). B. If the shaft in the problem above is fixed axially and rotated inside the sleeve at 2000 rpm, determine the resisting torque exerted by the oil and the power required to rotate the shaft in kilowatts (kW).
A sleeve of 10cm encases a vertical metal rod 3.0cm in diameter with radial clearance of 0.02mm. if when immersed in oil of viscosity 6.0 poise , the effective weight of the sleeve is 7.5N , will the sleeve slide down the rod and if so, at what velocity?
steel tape 0.5 mm thick and 20 mm wide is pulled by a force F through a slit opening 1.5 mm and length 15 mm. Considering that the tape is centered on the slit, that lubricating oil of viscosity µ = 0.4 Nm-2s? fills the gap spaces not occupied by the tape and that the maximum tape speed is 10 m/s, calculate the maximum force F. Expected Answer: Maximum Force = 4.8N
The velocity distribution for the flow of oil with dynamic viscosity of 0.05 Pa-s is given by u(y)=200y(0.1−y)u(y)=200y(0.1−y) where y is in meters. What is the shear stress at the bottom boundary in Pa? see picture
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 ?2/? and SG=0.9. Find the frictional resistance exerted by the oil on the shaft in Newtons (N).
A gas tanker carries fuel oil having density of 900kg/m3 and viscosity of 0.05kg/ms as shown in the figure. Thecapacity of the tanker is 20m3 and filling time is 40 minute. Please calculate the required input power of the pump tofill the empty tanker at the beginning of filling process. Note that total irriversible head loss is 2m and the efficiencyof the over-all pump is 82%. Please discuss the amount of required power during the filling process
An oil film of thickness 1.5 mm is used for lubrication between asquare plate of size 0.9 m × 0.9 m and an inclined plane having anangle of inclination 200. The weight of the square plate is 392.4 N andit slides down the plane with a uniform velocity of 0.2 m/s. Find thedynamic viscosity of the oil
the nord stream 2 is a pipeline network from used to pump and transport Russian oil to germany. 29286 gallons of oil can be transported per minute through the pipes with an average inside diameter of 50 inches. Given the oil ttranported has a density of 57.99 lbm/ft3 and a viscosity of an 0.0069625 lbm/fts. what is the reynolds number of flow?
A 400 mm diameter shaft is rotating at 200 rpm in a bearing of length 120 mm. If the thickness of oil film is 1.5 mm and the dynamic viscosity of the oil is 0.7 Ns/m2 determine: Power utilization in overcoming viscous resistance
It is desired to determine the surface tension of a particular fluid using a capillary-riseexperiment. Kienth used a 0.5 mm glass tube and found that the height of the liquidmeasured 30 mm with a contact angle of 30°. Kienth then performed viscosity measurements using an Ostwald viscometer. He found that the fluid takes 1.5 times slowerto flow through the viscometer relative to water with a density of 1000 kg/m? and aviscosity of 1.0 cP. It is previously known that the viscosity of the fluid is 1.35 cP. Whatis the surface tension of the liquid?
A skater weighing 500 N skates at 10 m/s and is supported by an average skating area of 10 cm2. If the viscosity of water is 1 centipoise and the coefficient of friction between skates and ice is 0.02, then find the thickness of thin film of water existing between the skates and the ice. Follow the methodologies in solving the problem; Given : Required: Schematic Diagram: Solution: