The square deforms into the position shown by the dashed lines in (Figure 1). The dimensions are S=49 mm, S′=54 mm, Δx1=5 mm, and Δx2=9 mm. Side D'B' remains horizontal. Determine the shear strain at D relative to the x, y axes.

Q: 1.42 As shown in the right Figure, a small-diameter water pipe passes through the 6-in.-thick…

A:

Q: 17. Air at 50% relative humidity has the same humidity ratio as air at 70 degrees F Drybulb and 90…

A:

Q: own, a member is fixed at the origin, point O, and has an applied force F, the tension in the rope,…

A:

Q: An Ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air…

A:

Q: Q.5) A steel bar OC with attached spring at B and cable at C can rotate freely in a horizontal plane…

A:

Q: 5. A composite cantilever beam, made of High Strength (HS) carbon/epoxy material with [04/304],…

A: Hi, We dont have the specfic software so we will solve this question manually.Write the given…

Q: the appropriate characteristic length and velocity scales for B.L. analysis are L and u.,…

A:

Q: The vane is moving at 80 ft/s when a jet of water having a velocity of 150 ft/s enters at A. The…

A:

Q: Consider the bar in Figure 2 loaded as shown. Determine the nodal displacements, stress in each…

A: Given:To find:(a) Nodal displacements.(b) Stress in each element.(c) Support reaction.

Q: Part (a) Find the efficiency of an ideal engine operating between these reservoirs. Remember the…

A: Given:Energy input from hot reservoir = Energy rejected to cold reservoir = Time = t = 0.21 sTo…

Q: 1) Carbon dioxide, as a gas, at 335 K is pumped at a very high pressure into an oil-well. If CO₂ has…

A:

Q: Saturated air at 40°F (4.4°C) is first preheated and then saturated adiabatically. This saturated…

A:

Q: A Д 2q a | P=2qa C q а В

A: Note:- As per the honor code and answering guidelines I can answer 1st question (As both questions…

Q: The bar has a cross-sectional areao of 490(10-6)m2. It is subjected to triangular axial distributed…

A: Area of the cross section  To determine:The average normal stress in the bar

Q: Lire 0.5 m 2.5m 1 of 1 Part A Determine the magnitude of the moment of the force F = {50i- 21 j-…

A: Force vector F = co-ordinates of A : (0 , 2 , 0)co-ordinates of B : (3.5 , 2.5 , 0)co-ordinates of D…

Q: SOLVE STEP BY STEP IN DIGITAL FORMAT DON'T USE AI | DON'T USE AI | DON'T USE AI | DON'T USE AI | A…

A: Given-Distance of  mass from centre of rotation Distance of  mass from centre of rotation To…

Q: Derive the overall probabilities of two closed systems, A & B, along with all necessary steps  using…

A:

Q: 2a q C 1 M=2qa² a B q=30kN/m A 1m 0.5m D P=20kN 1.5m E q=30kN/m 1m B

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: (Suppose you need to design a tension test machine capable of testing specimens that have nominal…

A: Given data:Ultimate stress, σu = 100 ksidiameter of the specimen, d = 0.5 in (from the given…

Q: Given two views of a multi-view drawing, draw the missing view and then create a 3D isometric sketch…

A: To determine:The missing right-hand view and an isometric view.Given:Two views of an object are…

Q: A 10' C B 10' E 10' 10' 20 kips 20 kips 20 kips H vy K M 10' 10' 20 kips 20 kips 20 kips 10' N 15'…

A:

Q: 9. A mass of 20 g stretches a spring 5 cm. Suppose that the mass is also attached to a viscous…

A: m=20 gdampimg constant u(0)=2u'(0)=0First, we calculate the spring constant, using the equation

Q: The 2014-T6 aluminum rod has a diameter of 0.7 in. and fits snugly between rigid supports at A and B…

A: Given:To find:Reaction force at A and B.

Q: Problem 8( Nitrogen gas at constant pipeline conditions of 200 kPa and 300 K passes slowly through a…

A:

Q: 12.60 A small 8-oz collar D can slide on portion AB of a rod which is bent as shown. Knowing that…

A: r = 24 in = 2 ft

Q: The assembly consists of two 10-kg bars which are pin connected. If the bars are released from rest…

A:

Q: Part B - Normal strain, cross-sectional area, load, and Poisson's ratio Four axially loaded members…

A: There are four cases in which all the components have different cross sectional areas and load and…

Q: The shaft is supported by three smooth journal bearings at A, B, and C. Determine the components of…

A: Given : system consists of forces applied in different directions supported by journal bearings.Find…

Q: = A straight bevel gear pair has the following data: Np 25; NG 50; P = 10; and 20° pressure angle.…

A: given;

Q: 3-20. Determine the tension developed in cables OD OB and the strut OC, required to support the…

A:

Q: m. nd Find the components of the equivalent force. Express the re Express the z, y, and z components…

A: The position vectors are-

Q: *4-116. Replace the loading acting on the frame by an equivalent resultant force and couple moment…

A:

Q: 1. Suppose a steel material of S.G of 7.8 is as attached to a wood of S.G. of 0.8 Shown below. If it…

A: Given:To find:Ratio of ?

Q: At a flow rate of 10 LPM, what will gonna happen if the pressure drops over 90 seconds from 0.657…

A: The flow rate given asthe time taken, pressure drop, the given pressure,

Q: F₁ F₂- F₂ A B с F3 -F3 D E F

A: Given Data:Applied forces: F1 (unknown), F2 = 11 kN, F3 = 9 kN, F4 = 6 kNDiameter at section B (dB)…

Q: 12. The composite bar in the figure is stress-free before the axial loads PI and P2 are applied.…

A: FBD of each material :where  δal is shortening length δst is lengthening lengthδbr is also…

Q: 480 mm B D PROBLEM 1.39 Link BC is 6 mm thick and is made of a steel with a 450-MPa ultimate…

A:

Q: A glass is cleaned in hot water and reaches a temperature of 50°C. The glass is placed on a table…

A:

Q: 3. The uniform L-shaped bar pivots freely at point P of the slider, which moves along the horizontal…

A: Let the total mass of the L-shaped bar be 'm'. The weight acting on the different points of the bar…

Q: Problem 17.127: Circular fins of uniform cross section, with diameter of 10 mm and length of 50 mm,…

A:

Q: Calculate the temperature in K of air at 13.2 MPa with a specific volume of 2.52×10-3 m3/kg using…

A:

Q: Problem 6: Continuity Principle Key 1. Water 2. Saturated soil 3. Dam-assume impervious (i.e., no…

A: From the given figure, the upstream point 'A' is shown as below.At Point 'A',The Presure head = 0 m…

Q: A roadway sign that weighs Py = 14 kN is supported by a structural pipe with an outside diameter of…

A: Py = 14 kNPz = 21 kNoutside diameter do = 340 mmthickness t = 10.5 mm So inner dia di = do - 2t =…

Q: Three kilograms of water at 30°C are placed in a piston cylinder device under 1.0 MPa absolute…

A: The mass of the water, The initial temperature of the water, The initial pressure of water, The…

Q: Drilling, diameter = 0.375 inches, feed is 0.003 inches/tooth, number of teeth is 2, rotation speed…

A: Given-To Find-Material Removal Rate (MRR)Power at the MotorPower at the ToolTorque at the Tool

Q: result of an hydrostatic pressure experi

A: Overview a hydrostatic pressure experiment typically involves providing a detailed analysis of the…

Q: Largest Member 2 Area = 34 P y P← -X Area = Member 4 A 4/2 P P ·x Member 1 Area = A y P P -X Member…

A: There are four cases in which all the components have different cross sectional areas and load.But…

Q: A cutting tool (0.250 in wide, rake angle 5°) is used to machine in orthogonal mode at 0.010 inch…

A:

Q: C 00

A: The area under the curve is-

Q: Q2. A 2 lb of steam, initially at 700 lbf/in.², 550°F undergoes a polytropic process in a piston-…

A: The mass of the steam, The initial pressure, The initial temperature, The final pressure, The…