The starting winding circuit of a capacitor start, induction run motor consists of a 15 Ω resistance and a 20 Ω inductive reactance. These components are in series with a 50 µF capacitor. The circuit is connected to a 120 V, 60 Hz source. Determine: the impedance of the series circuit. the current. the true power. the power factor

The starting winding circuit of a capacitor start, induction run motor consists of a 15 Ω resistance and a 20 Ω inductive reactance. These components are in series with a 50 µF capacitor. The circuit is connected to a 120 V, 60 Hz source. Determine: the impedance of the series circuit. the current. the true power. the power factor

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
A 400-V, 3-phase induction motor load takes 900 kVA at a power factor of 0.707. Calculate the KVA rating of the capacitor bank to raise the resultant power factor of the installation of 0.866 lagging. Find also the resultant power factor when the capacitors are in circuit and the motor load has fallen to 300 kVA at 0.5 power factor.
A single-phase motor takes 10A at a power factor of 0.7 lagging when connected to a 230V, 50 Hz supply. A capacitor bank is connected in parallel with the motor to raise the power factor to unity.i) Draw the phasor diagram before and after power factor correction with the supply voltage taken as the reference phasor. ii) Calculate the percentage change in the supply current after power factor correction.iii) Calculate the value of capacitance required.
An industrial plant consisting primarily of induction motor loads absorbs 500 kW at 0.6 power factor lagging. (a) Compute the required kVA rating of a shunt capacitor to improve the power factor to 0.9 lagging. (b) Calculate the resulting power factor if a synchronous motor rated at 375 kW with 90% efficiency operating at rated load and at unity power factor is added to the plant instead of the capacitor. Assume constant voltage.
A single-phase alternator connected to 6,600-V bus-bars has a synchronous impedance of 10Ω and a resistance of 1 Ω. If its excitation is such that on open circuit the p.d. would be 5000 V, calculate the maximum load the machine can supply to the external circuit before dropping out of step and the corresponding armature current and p.f. [2864 kW, 787 A, 0.551]
A single-phase motor is connected as shown inFigure to a 50-Hz network. The capacitor valueis chosen to obtain unity power factor. If V = 220 V,I = 20 A, and I1 = 25 A, find the capacitor value
A balance 3-phase, 220V, abc source initially has a load which is a 3-phase induction motor rated 60 Hp, 0.85 efficiency, 0.8 p.f. lagging. If it is desired to improve the power factor of the system from 0.8 to 0.95 pf lagging by adding a 3-phase synchronous motor that will operate at 0.85 pf leading. What is the KW input of the synchronous motor needed to do this?
A single-phase synchronous motor having a synchronous reactance of 5 ohms and negligible resistance is connected across a 2200-V supply. If the input power remains constant at 100 kW, calculate the generated e.m.f. when the power factor is 0.8 leading. Sketch the phasor diagram.
The impedance of the stator winding of a 440 V, star-connected, three-phase inductio nmotor is (0,2 + j0,8) Ω per phase and that of the rotor is (0,06 + j0,25) Ω per phase atstandstill. The turns ratio is 2. Using the approximate equivalent circuit, calculate therotor current and the power factor when the slip is reduced to 25% by injecting16,2 V/phase into the rotor circuit without any phase compensation.
A 3Ø, Y-connected alternator is rated at 1,600KVA, 13.5KV. The armature effective AC resistance per phase is 1.5Ω. The percentage regulation for a load of 1,280kW at unity power factor is 3.5%. Determine:(a) synchronous reactance of the alternator(b) %VR at full-load 0.8pf leading(c) What is the effect on %VR value if taken at half-load lagging pf? Justify andexplain briefly your answer on one(1) sentence.
A 60kVA, 220V, 50Hz, single phase alternator has effective armature resistance of 0.016 ohm and an armature leakage reactance of 0.07 ohm. Compute the voltage induced when the alternator is delivering at a load power factor of (a) unity; a. 225.2V b. 252.2V c. 522.2V d. 222.5V