The state of stress at a point in a member is shown on the element. Suppose that o, = -50 MPa , oy = -120 MPa, Try = -30 MPa Part A Determine the normal stress component acting on the plane AB. (Figure 1) Express your answer with the appropriate units. HA Value Units Submit Request Answer Figure 1 of 1 Part B A Determine the shear stress component acting on the plane AB. Express your answer with the appropriate units. HA ? 30% Tr'y = Value Units Submit Request Answer B

The state of stress at a point in a member is shown on the element. Suppose that o, = -50 MPa , oy = -120 MPa, Try = -30 MPa Part A Determine the normal stress component acting on the plane AB. (Figure 1) Express your answer with the appropriate units. HA Value Units Submit Request Answer Figure 1 of 1 Part B A Determine the shear stress component acting on the plane AB. Express your answer with the appropriate units. HA ? 30% Tr'y = Value Units Submit Request Answer B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

Given the stress cube below, represent the Mohr Circle, demonstrating the stepsfollowing:a) Calculation of main stresses and directions;b) Calculation of stresses in a plane of rotation ?, clockwise;c) Circle of Mohr.
The state of stress at a point in a member is shown on the element. Suppose that σx = -50MPa , σy = -120MPa , τxy = -30 MPa . Determine the normal stress component acting on the plane AB. σx′=?
Determine the equivalent state of stress on an element at the same point oriented 60 degrees clockwise with respect to the element shown in the figure below. Suppose that Sigma-x = 151 MPa, Sigma-y= 106 MPa. Determine sigma-x' in MPa. Express your answer to three significant figures. Do not include the units with your answers.
At room temperature (20°C), a 0.5-mm gap exists between the ends of the rods shown. The temperature eventually reaches a value of 139°C. Determine the normal stress in the aluminum rod.
The state of stress at a point in a member is shown on the element. Suppose that σx = -50 MPa , σy = -120 MPaMPa , τxy = -30 MPa . Determine the shear stress component acting on the plane AB. Tx`y`=?
The state of stress at a point in a solid component isshown in Figure P12.22. The stress magnitudes areσ n = 80MPa,σ t = 40 MPa, andτnt = 32 MPa, acting in the directionsindicated in the figure. Determine the normal and shearstress components acting on plane AB for a value ofβ = 35°
A copper bar with a rectangular cross sectionis held without stress between rigid supports (seefigure). Subsequently, the temperature of the bar israised 50°C.(a) Determine the stresses on all faces of theelements A and B, and show these stresseson sketches of the elements. (Assumeα = 17.5 x 10 6 / °C 2 and E = 120 GPa.)(b) If the shear stress at B is known to be 48 MPaat some inclination θ, find angle θ and showthe stresses on a sketch of a properly orientedelement.
The state of stress at a point can be described by σx = 40 MPa , σy = 64 MPa , and τxy = 18 MPa . A second coordinate system is rotated by θ = 25 ∘ A) What is the normal stress in the direction of the x′-axis? B) What is the shear stress in the y′-direction for the faces with a normal in the x′-direction? C) What is the normal stress in the direction of the y′-axis?
The yield stress for a zirconium-magnesium alloy is sY = 15.3 ksi. If a machine part is made of this material and a critical point in the material is subjected to in-plane principal stresses s1 and s2 = -0.5s1, determine the magnitude of s1 that will cause yielding according to the maximum shear stress theory.
A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 144 lbs is applied at the end of a 1.1 ft lever arm, causing the pipe to twist. What is the maximum stress in the pipe in psi? the correct answer is 28248 please show steps!!
Assume the plane stress element shown in Fig. E3-a represents the stress a geosynthetic membrane used in a mechanically stabilized earth wall. If the reference state of stress for this element results in the Mohr’s circle plot shown in Fig. E3-b, determine: The principal stresses. The principal directions (angles to the principal planes). The maximum in-plane shear stress. It is known that the seam, which is rotated 45 deg from the vertical as shown in Fig. E3-c, will fail if subjected to a tensile stress of 25 kPa or a shear stress of 1 kPa. Determine the normal stress and shear stress acting on the seam, and state if the seam will fail due to the loading indicated.
PLSS ANSWER ASAPPP Which is correct about spherical shell? a It has the same formula as hoop stress b The wall of the pressurized spherical vessel is subjected to uniform comporessive stress in all directions c It has the same formula as the tangential stress d The wall of the pressurized spherical vessel is subjected to uniform tensile stress in all directions