The fluctuating stresses listed in the table are found at a critical location of a component made of steel with Se= 40 ksi, Sy = 80 ksi, Sut = 110 ksi and f= 0.87. These stresses are applied on the part within 10 s. What is the accumulative damage of this part? What is the life of the part in hours if this stress pattern continues to repeat for the remained of the part's life? Use Goodman criterion and Miner's rule in your solution. Loading order |ơmin Omax Number of cycles -20 30 2. -10 50 3. -30 30 1

The fluctuating stresses listed in the table are found at a critical location of a component made of steel with Se= 40 ksi, Sy = 80 ksi, Sut = 110 ksi and f= 0.87. These stresses are applied on the part within 10 s. What is the accumulative damage of this part? What is the life of the part in hours if this stress pattern continues to repeat for the remained of the part's life? Use Goodman criterion and Miner's rule in your solution. Loading order |ơmin Omax Number of cycles -20 30 2. -10 50 3. -30 30 1

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.1P: The rails of a railroad track are welded together at their ends (to form continuous rails and thus...

See similar textbooks

Similar questions

The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
10.3. Consider the state of stress shown below that exists at a location within a component made up ofa brittle material, where this brittle material has tensile and compressive ultimate strengths ofσ UT = 170 MPa and σ UC = 850 MPa, respectively. Has the material failed at this location in thecomponent? Please include a free body diagram.
Bar of steel, (yield strenght Sy = 484 MPa) is subjected to the following stresses; σx = 176 MPa , σy = 116 MPa , τxy = 226 MPa Using the Maximum Shear Stress Theory (MSS) determine the factor of safety and check is the bar will fail or not.
Draw the tensile curves of the following materials, taking into account the appropriate elongation at break, modulus of elasticity and tensile stress, on the side stress-strain graph. a)Low carbon steel (Ecelik=200Gpa),(Syield=300MPa),(Stensile=400MPa) b)High carbon steel (Esteel=200GPa),(Stensile=700MPa) c)Aluminum (Ealuminum=70GPa), (Syield=200MPa),(Stensile=300MPa) d)Cast iron (Ecast iron=120GPa),(Stensile=200MPa)
1. A part made of Aluminum 6061-T6 has a yield strength = 400 MPa. For each stress state below, draw all 3 Mohr's circles, find the principal stresses, and calculate the safety factor against yield using both the distortion-energy (von Mises) and maximum shear stress (Tresca) criterions. (If relevant) A clearly labeled diagram (or diagrams) clearly pertaining to your analysis with a coordinate system and relevant labels. Final answer with appropriate units and significant figures. You can use the fprintf() command in MATLAB to format numerical results A 2-3 sentence reflection on your answer. Does it make sense? Why or why not? What are some implications?
answer this ; The factors of safety predicted at point H by the maximum shear stress theory of failure (Tresca criterion)
What are the three equations that represent the general form of Hooke’s law for a Triaxial state of stress?
Strength of Material TextbookTopic: Factor of Safety for Stress LimitsProvide step by step solution
Analyse the differences between the 2 attached stress-strain curves for 0.9% carbon steel and 0.15% carbon steel.
As indicated in Figure 4, a tensile stress is to be applied along the long axis (z-axis) of an aluminium rectangular bar. The width of each edge of the bar is w0 = 2.3 mm, and the length is l0 = 12 mm. The bar's modulus of elasticity and Poisson's ratio are respectively 69 GPa and 0.35. It is believed that the material is isotropic. a)If the elongation of the bar, △l needs to be increased, suggest one suitableparameter that should be change on the system. Consider the material of thespecimen is maintained with aluminium. Justify your answer in calculation.