The staves or vertical members of the wooden tank are held together using hoops having a thickness of 19 mm and a width of 54 mm. The spacing of hoops is 291 mm. The wooden tank has a radius of 479 mm. Determine the stress in hoops (kPa) if the tank is subjected to an internal gauge pressure of 17 kPa and this loading is transmitted directly to the hoops. s/2 s/2 O O B-

The staves or vertical members of the wooden tank are held together using hoops having a thickness of 19 mm and a width of 54 mm. The spacing of hoops is 291 mm. The wooden tank has a radius of 479 mm. Determine the stress in hoops (kPa) if the tank is subjected to an internal gauge pressure of 17 kPa and this loading is transmitted directly to the hoops. s/2 s/2 O O B-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

STRENGTH OF MATERIALS A boiler is constructed of 9mm thick steel plates that are fastened together at their ends using a butt joint consisting of two 9mm cover plates and rivets having a diameter of 10mm and spaced 60mm apart as shown. If the stream pressure in the boiler is 1.38MPa, determine (a) the circumferential stress in the boiler's plate apart from the steam, (b) the circumferential stress in the outer cover plate along the rivet line a-a, and (c) the shear stress in the rivets. 60 mm 0.78 m
Problem 2): A 20 mm diameter steel rod passes concentrically through a bronze tube (200+Q) mm long, 50 mm external diameter, and 40 mm internal diameter. The ends of the steel rod are threaded and provided with nuts and washers which are adjusted initially so that there is no end play at 25°C. 1. Assuming that there is no change in the thickness of the washers, if the stress produced in the steel is (200+Q) MN/m2 when one of the nuts is tightened, the pitch of the thread being 1 mm: Find the number of turns for the nut and stress in the bronze tube.2. If the temperature of the steel and bronze is then raised to 40°C find the changes that will occur in the stresses in both materials.The coefficient of linear expansion per C is 10 x10-6 for steel and 17 x10-6 for bronze. E for steel = 210 GN/m2 and, E for bronze = 100 GN/m2.Note: Q = 39
5.Compute the maximum shearing stress developed in a phosphor bronze spring having a mean diameter of 200 mm and consisting of 24 turns of 20-mm diameter wire when the spring is stretched 100 mm. Assume G = 42 GPa. Use Wahl formula.
The elliptical pipe carrying steam at 3.5 mPa has an outer major axis length of 500 mm and an outer minor axis length of 400 mm with a wall thickness of 10 mm. A gasket is inserted between the flange at end of the pipe , and a flat plate is attached using 40 mm diameter bolts to cap the end . The allowable Stress in the bolts is 80 Mpa. How many bolts must be used to hold the cap if there is an initial stress of 30 mPa ?
Determine the adequacy of a 600 mm diameter (internal) steel pipe of length 2500 m with a thickness of 20 mm if it is capable of carrying a maximum stress of 125 MPa. The pipe is connected to a reservoir whose water surface elevation is at elevation 200 m. and discharge freely into air. A valve at the lower end of the pipe (elev. 0 m) is to be closed quickly. Cwfor Hazen-William’s Equation is 120 for the pipe and take bulk modulus of the water equal to 2.07X106 KPa while modulus of elasticity for steel is 200,000 MPa.
Determine the adequacy of a 600 mm diameter (internal) steel pipe of length 2500 m with a thickness of 20 mm if it is capable of carrying a maximum stress of 125 MPa. The pipe is connected to a reservoir whose water surface elevation is at elevation 200 m. and discharge freely into air. A valve at the lower end of the pipe (elev. 0 m) is to be closed quickly. Cwfor Hazen-William’s Equation is 120 for the pipe and take bulk modulus of the water equal to 2.07X106KPa while modulus of elasticity for steel is 200,000 MPa.
A circular nylon pipe supports a downward load P, = 10kN, which is uniformly distributed around a cap plate at the top of the lower pipe. A second load Pa = 20 kN is applied upward at the top. The inner and outer diameters of the upper and lower parts of the pipe are d, = 30 mm, d, = 60 mm, d, = 55 mm, and d, = 65 mm, respectively. The bottom pipe has length 400 mm and the upper pipe has length 300 mm. Calculate the axial normal stress in each pipe segment. Calculate the strain in each pipe segment if the clongation of the upper pipe is 3.29 mm and the elongation of the bottom part is 1.25 mm.
A set of 5-lb forces are applied to the handles of the pliers as shown. Simple pinconnections exist at pts. B, C, D, and E. Determine the compressive force developed on thesmooth cylinder at pt. A.
A hollow tube ABCDE constructed of monel-metal is subjected to five torques acting in the directions shown. The tube has an outside diameter d2= 1.0in. The allowable shear stress is 14,950psi and the allowable rate of twist is 2.45degree/ft. Determine the maximum permissible inside diameter d1 of the tube in inches. Use G= 9500ksi.
The rigid block has a weight of 80 kips and is to be supported by posts A and B. These are made of A-36 steel, and the post-C. which is made of C 83400 red brass. If all the posts have the same original length before they are loaded, determine the average normal stress developed in each post when post C is heated so that its temperature is increased by 20∘F. Each post has a cross-sectional area of 8 in2.
A pressure vessel of 10-in. inner diameter and 0.25-in. wall thickness is fabricated from a 4-ft section of spirally welded pipe AB and is equipped with two rigid end plates. The gage pressure inside the ves-sel is 300 psi, and 10-kip centric axial forces P and P′ are applied to the end plates. Determine (a) the normal stress perpendicular to the weld, (b) the shearing stress parallel to the weld.
pls! write the complete solutions. upvote will be given! STRENGTH OF MATERIALS The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A is closed and the water pressure is 300 psi, determine the longitudinal and hoop stress developed in the wall of the pipe. Draw the state of stress on a volume element located on the wall and its corresponding Mohr's Circle.