The steel (E= 200 GPa) I-beam (W530 x 66, I= 351 x 10° mm) has a fixed support at A and is subjected to a distributed load over its entire length. The distributed load causes the roller support at B to settle downward (displace downward) by 10 mm. Determine the reactions at supports A and B. 70 kNm IC 10 mm 4.5 m 1.5 m

The steel (E= 200 GPa) I-beam (W530 x 66, I= 351 x 10° mm) has a fixed support at A and is subjected to a distributed load over its entire length. The distributed load causes the roller support at B to settle downward (displace downward) by 10 mm. Determine the reactions at supports A and B. 70 kNm IC 10 mm 4.5 m 1.5 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.25P: An S6 × 12.5 steel cantilever beam AB is supported by a steel tic rod at B as shown. The tie rod is...

See similar textbooks

Similar questions

A straight girder of uniform section and length L rests on supports at the ends, and is propped up by a third support in the middle. The weight of the girder and its load is w per unit length. If the central support does not yield, prove that it takes a load equal to (5/8)wL. ANSWER: 1.80cm and 2.48cm Please show solution to the answer.
Bronze [E= 100 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a cross-sectional area of 300 mm2 and link (2) has a cross-sectional area of 450 mm 2. For an applied load of P= 70 kN, determine the rigid beam deflection at point B.
In a 2.5 cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress in beam is 120 Mpa, determine the section modulus and The base and height of the beam if the base is 75% of its height mm.
The horizontal beam is assumed to be rigid while supporting the distributed load. Determine the angle of inclination of the beam after the load is applied. Each support consists of a wooden post with a diameter of 120 mm and an original length (unloaded) of 1.40 m- Consider E = 12 GPa
A symmetric I-section of size 180 mm × 40 mm, 8 mm thick is strengthened with 240 mm × 10 mm rectangular plate on top flange as shown is Fig. below. If permissible stress in the material is 150 N/mm^2, determine how much concentrated load the beam of this section can carry at centre of 4 m span. Given ends of beam are simply supported.
The horizontal beam ABC shown in thefigure is supported by columns BD and CE. Thebeam is prevented from moving horizontally bythe pin support at end A. Each column is pinned atits upper end to the beam, but at the lower ends, supportD is a sliding support and support E is pinned.Both columns are solid steel bars (E = 30 x 106 psi)of square cross section with width equal to 0.625 in.A load Q acts at distance a from column BD.(a) If the distance a = 12 in., what is the criticalvalue Qcr of the load?(b) If the distance a can be varied between 0 and40 in., what is the maximum possible value ofQcr? What is the corresponding value of thedistance a?
A steel [E = 25500 ksi] pipe column (1) with a cross-sectional area of A1 = 5.60 in.2 is connected at flange B to an aluminum alloy [E = 17500 ksi] pipe (2) with a cross-sectional area of A2 = 4.40 in.2. The assembly is connected to rigid supports at A and C. For the loading shown, determine the normal force in the steel pipe (1).
The outside diameter of the steel pipe shown is 220 mm and its wall thickness is 6.0 mm. The upper bearing plate has the same width as the reinforced concrete beam it supports. The total load on the column by the reinforced concrete beam is 550 kN. Determine: A. The length L of the rectangular upper bearing plate if its width is 275 mm. and the average bearing stress between the steel plate and the reinforced concrete beam is not to exceed 6.2 MPa.
A laminated wood beam consists of eight 2.25 in. × 5.00-in. planks glued together to form a section b = 5.00 in. wide by d = 18 in. deep, as shown. If the allowable strength of the glue in shear is 105 psi, determine(a) the maximum uniformly distributed load w that can be applied over the full length of the beam if the beam is simply supported and has a span of L = 19 ft. [Answer: w = 663.2 lb/ft]
The plate shown is made of UNS G10350 cold drawn steel (Sy=460 MPa and Su=550 MPa),and is fastened to an I beam made of UNS G10150 cold drawn steel (Sy=320 MPa and Su=385 MPa) by four rivets made of a steel with Sy=300 MPa and Su=365 MPa. Thickness of the plate is 10 mm and thickness of the flanges of the I beam is 15 mm. Diameter of the rivets is 20 mm. What safe load F (steady) can be supported by the riveted joint for a factor of safety of 2. Use distortion energy theory of failure.
In the case of buckling: Determine the maximum concentrated vertical load P that can act on the top of the pillar of the figure. The load is applied at the centroid of the column cross section. Consider that the column is set at the top and base, and that the beams only act constraining the column displacement in the x-axis direction. The pillar can buckle in the two x and y directions. Use: E = 30 GPa, L = 5 m, b = 15 cm, h = 30 cm, σesc = 60 MPa
Determine the vertical deflection of point A on the bent cantilever shown in figure below when loaded at A with a vertical load of 25 N. The cantilever is built in at B, and EI may be taken as constant throughout and equal to 450 N m2.