The solid 20-mm-diameter steel [E = 220 GPa] shaft supports two belt pulleys. Assume that the bearing at A can be idealized as a pin support and that the bearing at E can be idealized as a roller support. For the loading shown, determine the shaft deflection vo at pulley D. Assume P= 510 N, Q= 380 N, LAN = 300 mm, Lu: =190 mm, Les = 300 mm, L = 190 mm. Lạc L-DE

The solid 20-mm-diameter steel [E = 220 GPa] shaft supports two belt pulleys. Assume that the bearing at A can be idealized as a pin support and that the bearing at E can be idealized as a roller support. For the loading shown, determine the shaft deflection vo at pulley D. Assume P= 510 N, Q= 380 N, LAN = 300 mm, Lu: =190 mm, Les = 300 mm, L = 190 mm. Lạc L-DE

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.5.29P: A steel post (E=30×106) having thickness t = 1/8 in. and height L = 72 in. support a stop sign (see...

See similar textbooks

Similar questions

-7 Repeat Problem 2.3-5, but n include the weight of the bar. See Table I-I in Appendix I for the weight density of steel.
Repeat Problem 10.3-15 using L = 3.5 m, max = 3 mm, and EI = 800 kN·m2.
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
An aluminum pipe column (E = 10,400 ksi) with a length L = 10.0 ft has inside and outside diameters d1= 5.0 in. and d2= 6.0 in., respectively (sec figure). The column is supported only at the ends and may buckle in any direction. Calculate the critical load Pcrfor the following end conditions: (a) pinned-pinned, (b) fixed-free, (c) fixed-pinned, and (d) fixed-fixed.
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
Solve Problem 11.3-3 for a W 10 × 45 steel column having a length L = 28 ft.
An idealized column consists of rigid bar ABCD with a roller support at B and a roller and spring support at D. The spring constant at D. is ß = 750 N/m. Find the critical load Pcrof the column.
Repeat Problem 2.3-4, but now include the weight of the bar. Sec Table 1.1 in Appendix I for the weight density of steel.
A steel post (E=30×106) having thickness t = 1/8 in. and height L = 72 in. support a stop sign (see figure), where s = 12.5 in. The height of the post L is measured from the base to the centroid of the sign. The stop sign is subjected to wind pressure p = 20 lb/ft2 normal to its surface. Assume that the post is fixed at its base. What is the resultant load on the sign? (Sec Appendix E, Case 25, for properties of an octagon, n =8.) What is the maximum bending stress in the post? Repeat part (b) if the circular cut-outs arc eliminated over the height of the post.
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
A long slender column ABC is pinned at ends A and C and compressed by an axial force F (sec figure). At the midpoint B, lateral support is provided to prevent deflection in the plane of the figure. The column is a steel wide-flange section (W 250 × 67) with E = 200 GPa. The distance between lateral supports is L = 5.5 m. Calculate the allowable load P using a factor of safety n = 2.4, taking into account the possibility of Eu 1er buckling about cither principal centroidal axis (i.e., axis 1-1 or axis 2-2).