The steel pipe in (Figure 1) has an inner diameter of 3.41 in and an outer diameter of 3.66 in. If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point A, which is located on the outer surface of the pi

Q: 100 MPa 75 MPa 150 MPa

A:

Q: Determine the torsional stress in the thin-walled tube as shown:

A:

Q: Q/ If the cross section of the femur can be approximated as a circular tube, determine the state of…

A: Consider the diagram shown below for the femur. At point A, there will be a shear stress because of…

Q: Determine the state of stress at point A on the cross section of the shaft at section a–a. Show the…

A: The free-body diagram of point A is written as, On using the force equilibrium in the z-direction,…

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. If it is fixed at C…

A: Since the magnitude of the direct shear stress compared to the twisting and bending stresses is very…

Q: Determine the principal stresses, the maximum in-plane shear stress, and average normal stress.…

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A: Given: σx=62 MPaσy=-85 MPaτxy=56 MPa Solution: Sign convention: The tensile stress is positive  The…

Q: HWs. 1. The grains of wood in the board make an angle of 20° with the horizontal as shown. Using…

A: As per given question  Axial load=250N Angal=20° Width=25mm Thickness=60mm We have to draw mohr…

Q: Pulleys 1 and 2 of the rope and pulley system are connected and rotate as a unit. The radii of…

A: Given r1=0.1 m and r2=0.3 m d=0.015m m=225 kg Assuming no friction between any of the ropes and…

Q: the stresses at point A.

A: To find Stresses at point A

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A:

Q: Determine the maximum stress at the fillet of the filleted flat plate of 8 mm thickness as shown in…

A:

Q: The pedal crank for a bicycle has the cross section shown. If it is fixed to the gear at B and does…

A: Given data: The magnitude of the force subjected on the pedal is; F = 50 lb.   Draw the…

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A:

Q: Question 2 The bar has a cross-sectional area A and is subjected to the axial load P. Determine the…

A:

Q: Determine the equivalent state of stresses in an element at the point representing (a) the principal…

A:

Q: Q 4. Determine longitudinal stress in the cylinder if it has wall thickness of 7 mm and subjected to…

A: Given data: The thickness of the cylinder is t = 7 mm. The internal pressure is P = 100 MPa.

Q: The bolt is fixed to its support at C. If a force of 18 lb is applied to the wrench to tighten it,…

A: Given Data: The applied force is F = 18 lb. The length from force is l = 6 in. Diameter of shank is…

Q: Three forces of 500 lb, 800 lb, and 600 lb are applied to the end of the 2-in-diameter bar, as…

A:

Q: determine (a) the principal stresses and their principal planes, (b) the maximum shear stress and…

A:

Q: The grains of wood in the board make an angle of 20 with the horizontal as shown. Using Mohr's…

A:

Q: a) the principal stresses; and (b) the maximum in-plane shear stress.

A:

Q: a) The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an inner diameter of 20…

A: Given, di = 20 mm do = 28 mm D = 12 mm

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A:

Q: b. Determine the maximum value of the average normal stress points C and E. 0.4 m c. Determine the…

A: Here we have given P=20 kNdiameter d= 16mm∑mB=020(0.25)=-FCE(0.4)FCE=-12.5 kN (compr)

Q: Determine the average normal and shear stresses at a cross section (a-a) for e-65. The member has a…

A: Draw the F.B.D of the given cut section of the element.

Q: 1. The pipe shown below has a 1" outer diameter and a .125" wall thickness. Determine the state of…

A:

Q: The pressure in the tank is 2800 kPa, and an axial load of 130 kN is applied to the end of the tank…

A:

Q: An 8 mm thick cylindrical steel tank has an outside diameter of 600 mm and a length of 3 m. (a) when…

A: (a) The circumferential stress is 1.0889 MPa. (b) The longitudinal stress at the bottom is 0.5445…

Q: The rotor shaft of the helicopter is subjected to the tensile force and torque shown when the rotor…

A: Given, Diameter of shaft d = 6 in. Tensile force P = 50 kip Torque T = 10 kip.ft = 120 kip.in Area…

Q: Q.3. A steel rod of 20-mm diameter passes through a 0.8-m long brass tube of 35-mm external diameter…

A:

Q: Determine the stresses at point A. The circular solid shaft has a radius of 40 mm. 300 тm 200 mm B.…

A: Given Data, F= Eccentric shear force = 30 KN r= Radius of the shaft = 40mm According to the diagram…

Q: The bar has a diameter of 60 mm. If it is subjected to the force components as shown in the figure,…

A: Given data  d=60mm

Q: Q4- Draw Mohr's circle for the case as seen in Fig. 4. Determine the principal stresses and the…

A: According to the given information we have stress in x-direction and stress in the y-direction and…

Q: The beveled gear is subjected to the loads shown. Determine the stress components acting on the…

A: The free body diagram of beveled gear is shown below:

Q: Determine the equivalent state of stress on an element at the same point oriented 60°…

A: Given Data: The value of σx=150 MPa The value of σy=100 MPa The value of τxy=75 MPa The orientation…

Q: Determine the principal stresses, the maximum in-plane shear stress, and average normal stress.…

A: Given: The normal stress in the x-direction is бx=30 MPa The normal stress in the y-direction is…

Q: The state of plane stress at a point on the surface of the airplane fuselage is represented by the…

A: To find-  1. The maximum principal stresses and the maximum in plane shear specifying the…

Q: 2. The coping saw has an adjustable blade that is tightened with 8 mm a tension of 40 N. 3 mm A 75…

A:

Q: The truss members below have the shown length and they all have a solid diameter of 50 mm 1.…

A: given data diameter(d)=50mmlets take reaction force at A&F=RA &Rf  area (a)=π4…

Q: The joint is subjected to the force system shown. Determine the state of stress at points A and B,…

A: Let us consider the equilibrium of the lower section a-a Net force in the x-direction is zero…

Q: The 510-kg engine is suspended from the jib crane at the position shown. (Figure 1) Figure 2m 2 m 2…

A:

Q: Q2: Determine the state of stresses at point A on the cross section of the pipe shown in Fig. D=50mm…

A:

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. The pipe is fixed at…

A:

Q: If the box wrench is subjected to the 50-lb force, determine the principal stresses and maximum…

A: Draw the section a-a with shear force and bending moments.     Apply force equilibrium in the…

Q: he cylindrical tank with a spherical end-cap has an outer radius of r=1.5m and a wall thickness of…

A:

Q: The two cylindrical rod segments are fixed to the rigid walls such that there is a gap of 0.01 in.…

A: Write the given data with suitable variables. LCu=12 indCu=1.25 inLAl=6 indAl=1.25 inαAl=13×10-6…

Q: In the case of the infinitesimal elements shown in the figures, determine the normal and shear…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.