The steel propeller shaft ABCD carries the axial loads shown in the figure. Determine thechange in the length of the shaft caused by these loads. Use E = 29x10° psi for steel.0.75 in.6000 lb0.75 in.0.5 in.2000 lb4000 lbB|CD5 ft-4 ft 4 ft –a. Identify the type of deformation in each segment in the problem.b. Set up the equations of deformation that is required to solve the problem.c. Solve for the unknown variables using the equations derived previously.

The forces are shown in each member below: The internal forces in 3 segments are :- PAB = PBC…

The steel propeller shaft ABCD carries the axial loads shown in the figure. Determine the change in the length of the shaft caused by these loads. Use E = 29x10° psi for steel. 6000 lb 0.5 in. 0.75 in. 0.75 in. 2000 lb 4000 lb B| D 5 ft- 4 ft - 4 ft –

The steel propeller shaft ABCD carries the axial loads shown in the figure. Determine the change in the length of the shaft caused by these loads. Use E = 29x10° psi for steel. 6000 lb 0.5 in. 0.75 in. 0.75 in. 2000 lb 4000 lb B| D 5 ft- 4 ft - 4 ft –

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Related questions

Q: A cylindrical shaft made of steel of yield strength 700 MPa is subjected to static loads consisting…

A: Givenσy=700 MPaτ=σyF.S×0.58=7002.1×0.58=193 MPaM=10 kN=10000 NT=30 kN=30000 N

Q: The steel propeller shaft ABCD carries the axial loads shown in Figure. Determine the change in the…

A: Answer: The change in length of the shaft is 0.0136 in.

Q: The compound shaft shown in the figure consists of two steel [G = 80 GPa] pipe segments. The shaft…

A: Given Data: The modulus of rigidity of steel is, G=80 GPa=80 GPa×1000 MPaGPa=80000 MPa. The outside…

Q: 3.7-5 The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in.,…

Q: Calculate the maximum shear stresses from the torsional moment it the shaft between the points B and…

Q: Four pulleys are attached to the 50-mm-diameter aluminum shaft. If torques are applied to the…

Q: The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the…

A: Given data: - The torque at point A is TA = 2T. The torque at point B is TB = 3T. The allowable…

Q: A cylindrical bar shown in the figure below has axial loads applied as illustrated Calculate the…

Q: The solid shaft shown in the figure below is fixed at one end and has a lever at the other. The…

Q: A hollow tubular shaft will be used between the engine and the propeller of the boat as shown in the…

A: given data;outer diameter (do)=74mmthickness (t)=6mmengine power(P)=10KWspeed (n)=694rpmstress on…

Q: Determine the torsional stress of the cantilever shafts show in the figure below: C 200 5 KN.m T 15…

Q: The stress-strain diagram for a steel alloy having an original diameter of 12 mm and a gauge length…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: The rigid beam supports the load of 50 kN as in the figure below. Determine the displacement at B.…

A: As per given question The rigid beam supports the load of 50 kN as in the figure below. Determine…

Q: Useful equations; o = E A 1. The steel shaft carries the axial loads as shown in the figure below.…

A: Given axial load action on stepped shaft as shown below

Q: Q3: A shaft made of 40 C 8 steel is used to drive a machine. It rotates at 1500 r.p.m. The pulleys…

A: A torque, or moment of a force, is a measurement of a force's proclivity to cause a body to rotate.…

Q: Two shafts are connected by gears. The diameter of the two shafts is 1.5 in. They have the same…

A: Given: Diameter of two shafts (D)=1.5in or 0.125ftShear modulus G=11.2×106Radius of gear E=4in or…

Q: Problem No. 3. The compound shaft has the following properties: G in both Segment 1 Segment 1…

A: Calculate the inner diameter of the shaft 1. d1=D1-2t1 Here, D1 is the outer diameter of shaft 1, d1…

Q: The assembly shown in Figure consists of an aluminum tube AB having a cross-sectional area of 400…

Q: Consider the compound shaft KC which is compose of a 1200mm long solid rod fitted snuggly into an…

Q: The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the…

Q: The figure shows a special spanner used to tighten screwed components. A torque is applied at the…

Q: Q2c) The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in…

A: Given: Solution:

Q: Find the diameter of shaft A according to Tresca and Vonmisses criteria.

Q: 1.8 Find the maximum allowable value of P for the column. The cross-sectional areas and working…

A: Given Take the last column only Stress = 120 MPa Area, A = 500 mm2 Find Load, P

Q: A high strength drill rod used for boring a hole in the earth has a diameter of 50 mm. The allowable…

Q: 100 kN Stiff loading plate 10 cm 10 cm 10 cm 25 cm E= 200 GPa E = 200 GPa E= 70 GPa

Q: Determine the total deformation of the steel rod shown in figure under the given loads. Take the…

Q: 2.44 The figure shows the cross section of a circular steel tube that is filled with concrete and…

A: GivenP=200kipEst=29×106 psiEco=3.5×106 psi

Q: The assembly consists of a bronze tube (length = 1200 mm) and a threaded steel bolt. The pitch of…

A: Given: tube→BronzeBrBolt→SteelStcross sectional areas: ABr=1350 mm2ASt=675 mm2Initial…

Q: A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure. Calculate…

A: given: Dc=150mm Ds=100mm σ=100MPa Maximum axial load between the collar and plate. P=σ×A…

Q: 1- The shaft shown in the below Fig. consists of a 75-mm diameter aluminum segment rigidly joined to…

Q: The hollow shaft shown in the figure below is fixed at one end and has a lever at the other. The…

Q: 6. Determine the largest weight W that can be supported safely by the structure shown in the figure.…

A: Given:σAB=16,000 psiσBC=760 psiAAB=0.5 in2ABC=16 in2

Q: A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure. Calculate…

Q: ions of the cross section of the leading edge and torsion box of an airplane wing ted as shown. If…

Q: A solid shaft with a diameter of 20 mm is shown below. The shaft is fixed at points A and B. In the…

A: As per given question question a) Draw a torque diagram for this shaft. b) Determine the maximum…

Q: A tube of 50 mm outside diameter and 2mm thickness is attached at the end by means of rigid flanges…

Q: Rigid beam AB rests on the two short posts shown in Fig. 4–7a. AC is made of steel and has a…

A: Solution:

Q: Q1) A beam is loaded as shown in Figure: a) Determine the bearing stress at points A. b) Calculate…

Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…

A: Step by step solution is given below

Q: (15) The figure shows the free-body diagram of a connecting-link portion having stress concentration…

Q: The state of stress acting at a critical point on a wrench is shown in the figure. Determine the…

A: Given: The state of stress is given as Here, σx=300 MPaτxy=150 MPa

Q: 6 kN/m 4 kN/m 15 m- 2 m What is the concentrated load of the rectangular loading as shown in the…

A: This numerical is related to the strength of material portion. Concept used while solving this…

Q: Please answer quick. Thanks

Q: 1. A steel rod of 25 mm diameter is enclosed centrally in a copper hollow tube of external diameter…

A: Given: Diameter of the steel rod is 25 mm. Internal and external diameter of the copper tube are 30…

Q: The solid steel shaft shown below has a diameter of 20 mm and fixed to rigid wall at A and B. If it…

Q: For the given figure below, the beam is 57.4 m long. It has a rectangular cross-section area with…

A: Consider the diagram as shown below for the given beam. Here Fs is the spring force.

Q: Question #4 Bar (1) in the figure has a cross-sectional area of 0.75 in². If the normal stress in…

Q: 1. The steel shaft carries the axial loads as shown in the figure below. Determine the change in…

A: Consider the free body diagram:

Question

The steel propeller shaft ABCD carries the axial loads shown in the figure. Determine the
change in the length of the shaft caused by these loads. Use E = 29x10° psi for steel.
0.75 in.
6000 lb
0.75 in.
0.5 in.
2000 lb
4000 lb
B|
C
D
5 ft-
4 ft 4 ft –
a. Identify the type of deformation in each segment in the problem.
b. Set up the equations of deformation that is required to solve the problem.
c. Solve for the unknown variables using the equations derived previously.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
Solve the preceding problem if the thickness of the steel plate is. t = 12 mm. the gage readings are x = 530 × 10-6 (elongation) and y = -210 -× l0-6 (shortening), the modulus is E = 200 GPa, and Poisson’s ratio is v = 0.30.
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
A metal bar AB of a weight Ills suspended by a system of steel wires arranged as shown in the figure. The diameter of the wires is 5/64 in., and the yield stress of the steel is 65 ksi. Determine the maximum permissible weight W max for a factor of safety of 1.9 with respect to yielding.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
, Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14 kN/m, and L = L2 m.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
The composite shaft shown in the figure is manufactured by shrink-Fitting a steel sleeve over a brass core so that the two parts act as a single solid bar in torsion. The outer diameters of the two parts are dY= 40 mm for the brass core and d2= 50 mm for the steel sleeve. The shear moduli of elasticity are Gb= 36 GPa for the brass and Gs= 80 GPa for the steel. (a) Assuming that the allowable shear stresses in the brass and steel are rb= 48 MPa and ts= 80 MPa, respectively, determine the maximum permissible torque Tmax that may be applied to the shaft. (b) If the applied torque T = 2500 kN · m, find the required diameter d2so that allowable shear stress t3is reached in the steel.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.