The steel shaft with two different diameters rotates at 4.1 Hz. The power supplied to gear C is 52 kW, of which 21.3 kW is removed by gear B. Find the angle of rotation of gear A relative to gear Cif d = 59.3 %3D mm, h = 67.9 mm, L = 5 m, M = 2.2 m, and G = 83.86 %3D %3D Gpa. Round off the final answer to two decimal places. A B d EL l M→| - L

The steel shaft with two different diameters rotates at 4.1 Hz. The power supplied to gear C is 52 kW, of which 21.3 kW is removed by gear B. Find the angle of rotation of gear A relative to gear Cif d = 59.3 %3D mm, h = 67.9 mm, L = 5 m, M = 2.2 m, and G = 83.86 %3D %3D Gpa. Round off the final answer to two decimal places. A B d EL l M→| - L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

11 A cylindrical caisson having an outside diameter of 9 m floats in sea water with its axis vertical and its lower end submerged 9 m, below the water surface. If its center of gravity is on the vertical axis and is 3.6 m above the bottom. a. Determine the value of ??? b. Find the true metacentric height. c. Find the righting couple when the caisson is tipped through an angle of 8°
q=3.15 kn/m , a=3.15m
A cantilever beam carries a trapezoidaldistributed load (see figure). Let wB = 2.5 kN/m,wA = 5.0 kN/m, and L = 2.5 m. The beam has amodulus E = 45GPa and a rectangular cross sectionwith width b = 200 mm and depth h = 300 mm.Use the method of superposition and Cases 1 and8 in Table H-1 to calculate the def lection and rotationat B.
If the e = 45°, and the bar 0Q is rotating in the counterclockwise direction at 1.6 rad/s, which of the following is the velocity of the slider P?.
I WILL RATE! 1. What is the Horizontal Reaction at A? A. 0 B. 10 kN (to the right) C. 10 kN (to the left) D. 5 kN (to the left) 2. What is the Vertical Reaction at A? A. 11.67 kN upwardsB. 20.33 kN upwardsC. 32 kN upwardsD. 8 kN downwards 3. What is the Vertical Reaction at H? A. 20.33 kN upwardB. 11.67 kN upwardC. 32 kN upwardD. 8 kN downward 4. What is the Vertical Deflection at F? A. 2.74 mm downwardB. 0.42 mm downwardC. 0.36 mm upwardD. 1.17 mm upward
Determine the magnitude of the reaction at the bottom of the ladder. The top of the 15kg ladder is leaning against a very smooth vertical wall. Assume thatbthe mass center of the painter is directly above his feet and that the coefficient of friction between the horizontak ground and ladder is 0.25
given data : the slope of the dam 2v/1h so the height of the dam 12 m/ the all width of the dam will be 6 m (the width of the rectangular part is b-6)/ the depth of the dam 60m coefficient of sheer resistance = 0.75 gamma concrete 24 KN/m2 tailwater level of water converted into the channel directly behind the dam is 0.5 m (you will see that detail right of the picture drawn) the strip is 1 m (a force acting from water to dam ) height of the dam 12m height of water in the dam 10 m questions? 1- calculate all force in the picture W1/W2/u(uplift force)/Fh1/Fh2?(horizontal and vertical forces must all be calculated ) 2-Determine the dam weight needed to achieve a sliding factor of safety of 1.5 3-Determine the moments imposed at the dam toe. 4-Determine the dam weight needed to achieve an overturning factor of safety of 2. 5-Assuming that the dam downstream is with a slope of 1V/2H determine the dam base width to satisfy the stability requirements? 6-At the dam bottom an emergency…
A cylindrical caisson having an outside diameter of 7m floats in sea water sg=1.03 with its axis vertical and its lower end submerged 6m below the water surface. If its center of gravity is on the vertical axis and is 3m above the sea water surface. a. Determine the value of MBO, in meters b.Find the true metacentric height in meters is the caisson stable? c. find the restoring or upsetting couple, in kN-m, when the caisson is tipped through an angle of 9degree.
The moment diagram (answer in kips) P=8.3 kips, b = 23 ft, h=13 ft
A wooden cylinder (sg=0.61) is placedvertically in oil with specifc gravity of 0.85. Determine the metacentric height.
A new cast iron pipe must carry 1.2 m3/2 at a head loss of 5m per km length of the pipe. Compute the diameter of the pipe in mm using n= 0.019 Choices: A. 1210.47 B. 1012.74 C. 2101.74 D.112.47
Using Area-Moment Method, determine the deflection at the overhanging end in mm. Given: P = 4.2kN , w = 8.6 kN/m , a = 1.6m , b = 1.2m , c = 0.7m , E = 10 GPa , I = 20x106 mm4