The steel strip has a uniform thickness of 50 mm. Compute the elongation of the strip caused by the 500-kN axial force. The modulus of elasticity of steel is 200 GPa. 1000 mm- 1000 mm- 500 kN 500 kN -120 mm 50 mm 50 mm Match each item to a choice: Choices: 1.356 mm # 0.6725 mm # 0.678 mm # 1.345 mm #1.251 mm # 0.6253 mm ::

The steel strip has a uniform thickness of 50 mm. Compute the elongation of the strip caused by the 500-kN axial force. The modulus of elasticity of steel is 200 GPa. 1000 mm- 1000 mm- 500 kN 500 kN -120 mm 50 mm 50 mm Match each item to a choice: Choices: 1.356 mm # 0.6725 mm # 0.678 mm # 1.345 mm #1.251 mm # 0.6253 mm ::

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The steel strip has a uniform thickness of 50 mm. Compute the elongation of the strip caused by the 500-kN axial force. The modulus of elasticity of steel is 200 GPa.
37) A tensile test specimen has a gage length =3.0 inches and a diameter=0.75 inches. Yielding occurs at a load of 38000 lbs. The corresponding gage length 3.0103 inches (neglect the .2% yield point). The maximum load of 54000lb is reached at gage length 3.453 inches. Determine the modulus of elasticity. (Neglect the .2% offset and round to the nearest whole Msi)
A bar has a length of 200 mm and cross-sectional area of 7500 mm2. Determine the modulus ofelasticity of the material if it is subjected to an axial tensile load of 50 kN and stretches 0.075 mm.The material has linear-elastic behavior.
Calculate the safety of the cylinder pivot pin in relation to the yield. The tensile yield strength of the pin material is ReL=600MPa. The dimensions of the structure are: x1 = 10 mm x2 = 120 mm y1 = 110 mmy2 = 798 mm Piston rod = φ32mm Cylinder pivot pin = φ25mm Pliers pivot pin = φ30mm The clamping force of the pliers is 6000N Answer to one decimal place !!
The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mm diameter and 100 mm gage length is determined after its tensile strength test as follows. Based on the stressstrain diagram determine the followings properties of the material (Poisson’s ratio of the material is 0.32) :
A hydrostatic compressive stress applied to a material with cubic symmetry results in a dilation of -10-5. The three independent elastic constants of the material are C11 = 50 GPa, C12 = 40 GPa and C44 = 32 GPa. Write an expression for the generalized Hooke’s law for the material and compute the applied hydrostatic stress. Dilation ∆ = ε_11 + ε_22 + ε_33
A brass rod of diameter 50mm and of length 250mm which is subjected to a tensile liad of 300kN when the extension of the rid is 0.10mm. Calculate: Cross-sectional area (b) Stress (c)strain (d) Young's modulus
A cylindrical specimen of a titanium alloy having original diameter of 2.96 mm experiences elasticdeformation when a tensile load of 2500 N is applied. Compute the maximum length of the specimenbefore deformation if the maximum allowable elongation is 0.43 mm. Note: Etitanium = 107 GPa.
The ply stress σα was calculated for AS1/3501-6 Graphite/Epoxy laminates [0/+-45]s under load with N1=10,000 N/m and N2=N6=0. When the strength of this material is as follows, determine the stability of the laminate according to the maximum stress theory.
Which of the followings can be found out by calculating the area only under the linear portion (elastic region) and the area under the whole stress strain graph on the same graph? A ) Resillience - Toughness B ) Hardness - Toughness C ) Endurance - Strength D ) Strength - Resillience
Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Plot the diagram, and determine the modulus of elasticity and the modulus of resilience.
A square bar subjected to a tensile load of 100kN having a gauge length of 200mm extends to a length of 0.19mm . Given the tensile strength as 200 MPa , determine ( 1 ) Side of the bar ( express in mm ) Final length ( express in mm ) Modulus of elasticity ( express )