The structure shown consists of a single member ABCDE with a pin support at A and a roller support at E. Points B and D are at the midpoints of their respective segments. Determine the internal moment acting on I which are located immediately to the left of C. Take N = 5 kN, O = 4 kN, and P = 3 kN.

Q: 800 CFM of air at 90 °F, 50% rh is cooled to saturation. Determine the rate of heat transfer for the…

A: Given:  Inlet air flow rate = 800 CFM T1 = 90 oF RH = 50% cooled till saturation condition To find:…

Q: 5) Calculate the total heat energy removed during making of 1.5 kg ice cream. The initial…

A:

Q: Cold working is the good way to shape brittle material Select one: O True O False

A: Cold working  is a  metal working process in which metal is reshaped below its recrystallization…

Q: Case 1 1.3. dia=4 mm dia=2 mm dia=4 mm V Case 2 dia=2 mm, X 14 mm Case 3 dia=4 mm dia=8 mm dia=4 mm…

A:

Q: A torque T is applied, as shown below, to a solid shaft with built-in ends. Prove that the resisting…

A: Given  Torque T is applied at a distance a from one end as shown in below figure

Q: 5-65 A well-insulated valve is used to throttle steam 3 MPa and 350°C to 2 MPa. Determine the final…

A: Given:Initial pressure of steam, P1=8 MPaInitial temperature of steam, T1=350°CFinal pressure of…

Q: How long will in seconds it take to saw a rectangular piece of stainless steel plate 2.5 ft long and…

A: Length of cut=2.5ft Width=1.75ft To find time.required in saw

Q: Which factors can be varied to control the thickness of the metal deposited over the electrode in…

A: following is the answer to the above question-

Q: Determine the COP of a refrigerator that removes heat from the food compartment at a rate of 5040…

A:

Q: In a steady flow apparatus, a fluid enters with a specific volume of 0.30 m3 /kg, a pressure of 540…

A:

Q: Question 6. RAX B M F E RAY F₁ ne here to search C KN The figure above is a pin-joint frame with…

A:

Q: A heat transfer mechanism involving heat energy from molecule to molecule mainly in fluids is…

A:

Q: A fluid has a volume of 8.7m^3 and a weighs 53500N. Determine its unit density in kg/m^3 Choices…

A:

Q: Water at the rate of 86 kg/min is heated from 20 to 70-C by an oil having a specific heat of 1.9…

A:

Q: Explain the importance of spectroscopy on the properties of manufactured castings?

A:

Q: Question 1. RAX RAY M F₂ 8 F₁ KN D The figure above is a pin-joint frame with angle = 40° between…

A: Introduction In this problem, we will compute the force on the given structure's members AB and AF.…

Q: An adiabatic pump is to be used to compress saturated liquid water at 10 kPa to a pressure to 15 MPa…

A:

Q: An Ocean Thermal Energy Conversion (OTEC) power plant built in Hawaii in 1987 was designed to…

A:

Q: The Questions Question 4. X Given, B C The above figure (not drawn to scale) shows a 6 m long beam…

A:

Q: Rod Mills, Ball Mills and Autogenous Mills are different types of tumbling mills used in the…

A: The all types of mills such as Rod Mills, Ball Mills have the same grinding mechanisms. The grinding…

Q: Q11. Fig.11 shows the four-bar linkage of a cutting machine where the cutter is placed at point W.…

A:

Q: 4. Two members of a truss apply the forces shown to the gusset plate. a. If the Resultant of these…

A:

Q: c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) -…

A:

Q: A subsonic diffuser that __________ A. can increase the mass flow rate B.…

A: concept subsonic meaning velocity of fluid is less than the velocity of sound in given medium…

Q: A compressor handles 3500 cfm of air as measured at intake of 14.5 psia and 75°F. At discharge, p2 =…

A: Given data: Q˙=3500 cfmP1=14.5 psiaP2=25 psiaT1=75°FT2= 190°FV1=40 fpsV2=120 fps

Q: Convert the following into S.I. units, show complete solution, Do not use conversion table in…

A:

Q: A swimming pool Wby Y by h deep is to be emptied by gravit Assuming an average pipe friction factor…

A: Fluid dynamics are represented by Bernoulli's theorem. The total energy in the system remains…

Q: Find the velocity and acceleration of slider F. Also find the angular acceleration of links EPD and…

A:

Q: Grip. In the engineering design of handles (such as on manual and powered hand tools) and rails…

A: For solution refer below images.

Q: Consider 0.60 kg of austenite containing 1.3 wt% C, cooled to below 727°C (1341°F). Using the…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: Which of these are the steps involved in Deming's wheel (PDCA) plan, do, check, analyse Oplan,…

A:

Q: The above figure (not drawn to scale) shows a 6 m long beam subjected to forces F₁ and F₂. Given, F₁…

A: Given data: F1=80 kNF2=50 kNX=2 mY=1.5 m   It is required to determine the reaction forces at the…

Q: The machine element shown is fabricated from steel, where h = 64 mm. The density of steel is 7850…

A:

Q: Draw a symbol 5/2-way directional control valve, normally open where the left end is pneumatically…

A:

Q: The tractor is used to lift the 50-kg load B with the 27-m long rope, boom, and pulley system. The…

A:

Q: Find the velocity and acceleration of slider F. Also find the angular acceleration of links EPD and…

A: Given: To find: Velocity and acceleration of slider F Angular acceleration of links EPD and EF

Q: Oil with a density of 917kg/m3917kg/m3 is flowing smoothly through a pipe, as shown. In the lower…

A: Given:Oil density, ρ=917 kg/m3Velocity at lower portion, v1=2.24 m/sGauge pressure at lower portion,…

Q: A particle is located at x = a (a > 0) at t= 0. It moves toward = 0 in such a way that its velocity…

A:

Q: 3) A hot cup of coffee at 90 °C is placed on the table in a room at 22 °C. After some time a thermal…

A: During thermal equilibrium between coffee and it's surrounding, heat lost by coffee will be equal to…

Q: A circular pipe flow, the diameter d=50mm, mean velocity of water flow in the pipe v=1.5m/s,…

A:

Q: A closed ended, thick-walled cylinder, manufactured from silicon material is designed to contain…

A: Given data, Outer radius of the cylinder, ro = 0.3 m Inner radius of the cylinder, ri = 0.1 m…

Q: A disk rotates about an axis through its center. Point A is located on its rim and point B is…

A:

Q: Which of the following is independent of flow velocity? a. Transverse diffusion b. Longitudinal…

A: Eddy diffusion is independent of flow Velocity.

Q: If the tank is held so that the top is 3.0 m below the surface of water, what is the force on the…

A: Write the given diagrams.

Q: What are the that must be met in the metal used in the manufacture of the metal mold conditions

A: introduction; metal mold should be used in casting process for making desired dimension of object.…

Q: 2/131 A car P travels along a straight road with a con- stant speed v= 65 mi/hr. At the instant when…

A: Given data: v=65 mi/hrθ=60°h=100 ftr˙=?θ˙=?   The value x in terms of h and theta can be expressed…

Q: If the Radius of a elbow is 6”, and the duct Diameter is 3”, what is the loss factor if the elbow is…

A: Given data :- the Radius of an elbow (R)= 6 in the duct Diameter (D) =3 in To find :- the loss…

Q: P X 4 m 4 m A 5 m 3 m

A: Given,

Q: Find the velocity and acceleration of slider F. Also find the angular acceleration of links EPD and…

A:

Q: A car moves along a straight line from A to B with uniform acceleration of 0.66m/s². The time taken…

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.