The suitable terms for the blanks in the statement ."To change from psig to psia , you must ass __________ to psig."

Q: Creo practice exercise Using the Creo parametric sketch the following: GIVEN - PICTORIAL VIEW DRAW-…

A:

Q: What is the method of design called?

A: A design method is a set of various procedures that are carried out while designing planning to…

Q: Need part d asap Thanks!

A: Given data: Tm,i=20°Cp=1 atmd=25 mml=1.5 mm˙=6×10-4 kg/s Need to determine Reynolds number, rate of…

Q: What is the service life

A: Introduction: While purchasing any equipment for industrial/household purpose, one of the most…

Q: Conduct a lock-out and tag-out activity in the oil rig to repair the drilling equipment and…

A: the step which we take to conducting lockout tag out activity in oil rig for drilling machine…

Q: What is a solution to the following environmental risks in a SADA system Temperature Corrosion…

A: SADA system stands for Solar Array Drive Assemblies. These are the system in which the solar array…

Q: The correct choice is what

A:

Q: Mechanical working of metal is another name for_______________. a. Machining process b. Metal…

A: Mechanical working of metal is another name for Forming process. Answer: d. Forming Process

Q: Derive the statement is true or false

A: Given; Any thermodynamic cycle operating between two temperature limits is reversible if the product…

Q: 1. wolHk, 1+ užmgr 2. wol1+ u/Hkmgr 3. wolu/1+ µžmgr 1 + ufmgr 4. wol 1+ ui/umgr

A: option 2 is correct answer

Q: What is the forecast for the month of March.

A: Demand and forecast for February are; D=12000 F=10275 Smoothening co-efficient=025

Q: Give a long definition of what they do in the following aviation terminology. 4.paint shop 5. sheet…

A: Given Aviation manufacturing techniques To find Definition paint shop Definition sheet metal shop

Q: how did they get Fc

A:

Q: Most of the CTDS representing Engineering products are: O 3-levels. O 2-levels. O 4-levels. O…

A: Solution:

Q: Quest A A vel find + Solutic

A: GivenV→=axi^+byj^  where a=1and b=1

Q: In next generation reactors, such as the super critical water reactor, the reactor may operate in a…

A: SCWRs are light-water-cooled, high-temperature, high-pressure reactors that run above water's…

Q: State the purpose of the different sections that make up a typical automotive work environment

A: To find :- State the purpose of the different sections that make up at typical automotive work…

Q: 86) ATF contains additives to control which is caused by high temperature conditions.

A: A transmission system is used in the gearbox. The gearbox contains gear and gear trains that are…

Q: The tools and techniques used in CPS make the process А. fun В. enganging C. O collaborative D. O…

A: All listed answer.

Q: ) What do you know about Pro/Engineer software and its applications in the field of Mechanical…

A: Computer aided design or drafting is the utilization of a computer to help the creation alter,…

Q: What does SPC stand for?

A: SPC stands for statistical process control, which is the application of statistical instruments and…

Q: How to do the rest sub part

A: Given  Length, L = 10 cm  Area, A = 2 x 2 cm2 Find   Tensile strength   Change in length

Q: Give a situation where Lock-Out Tag-Out (LOTO) is needed. Why is it important?

A: LOTO (Lock Out Tag Out)  LOTO is a technical term basically used to  physical restraint of all…

Q: ood work on the promblem but the process is a bit hard to read, can you express

A: Given data as per question Tensile axial force, F=4500 N Outer diameter of tube, do=25 mm Inside…

Q: 16)In which process Catcher is used

A: Catcher is used in abrasive water jet machining According to question option c is absolutely correct

Q: What is the applications Center of Pressure

A: Center of pressure: It is the point at which the total sum of a pressure field acts on an object…

Q: Mechanical working of metal is another name for O a. Casting process O b. Machining process O c.…

A: Mechanical working is forming process .. there are two types of working cold and hot working.

Q: are using to produce for manufacturing a component.

A: The machine is used to hold the workpiece and tool and provides the required motion to the tool in…

Q: Identify the wrong statement in the following options.

A: option-A this statement is correct because standard helps the consumer to mantain the quality as…

Q: 3- List two reason, to keep low pressure drop across the production system. 5- W... a

A: Pressure drop is the most common and significant problem observed in production system. It basically…

Q: The mechanism of material removal in EDM process is: A) Erosion and Cavitations B) Cavitations and…

A: Electrical discharge machining(EDM):  This process works on the principle of spark generation and…

Q: sketch the figure in auto cad and mentions a few steps to sketch the figure

A:

Q: maximum level of inventory level.

A: Given; In a machine shop;  Diameter of pins,d= 15 mmProduction rate of pins is= 1000/ monthOr,…

Q: The process best in terms of close control of tolerance and surface finish IS Casting Joining All of…

A: 1) Machining 2) high melting point material 3) all of the above

Q: out and Tagout

A: given: Explain the difference between Lockout and Tagout

Q: 31 How can we prevent and control noise pollution in the workplace?

A: Noise pollution:  An excessive unwanted sound which have harmful effects on human health and…

Q: “If the difference between the amount entering the production and the amount obtained as a result of…

A: When we are manufacturing a product,  Certain amount of resource is used for its production.…

Q: Explain

A:

Q: $11. Match List I List II A. Die-sinking B. Deburring C. Fine hole drilling (thin material) D.…

A: Match the given lists

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.