3- List two reason, to keep low pressure drop across the production system. 5- W... a

Q: Q2/ In an axial flow compresse

A:

Q: One of the following is not used to reduce the setup time? a. Using power clamp b. Using softer raw…

A: The setup time can be reduced by - Eliminating waste Using power clamp Design for manufacturability…

Q: An installer can work 63⁄4 hours each day at a worksite. The installer will need303⁄8 hours to do a…

A: Given Data⇒ Time for which installer can work at a site a dayt=634 hours Time needed to install a…

Q: Describe the process of Feedforward Regulation system?

A: In feedforward regulation system controller identifies the errors within the system before output…

Q: 3. Why is maintenance schedule needed by the maintenance team/department ?

A: Maintenance schedule is same thing as planned maintenance. It is basically required for proper…

Q: Guardrails must be installed on any work surface elevated ft or above.

A: It is required to fill the blank

Q: Draw the Ts diagram of the whole process

A:

Q: Taw un a heat balance sheet for t

A:

Q: What is control volume?

A: A control volume is a system or space under observation that can exchange mass and energy from the…

Q: an angl ng in a w ing attacl is incline

A:

Q: shadow price

A: Given;  Determine  the shadow price of the source? Where,  In a linear programming problem, if a…

Q: Discuss drying and milling machineries

A: Drying milling machinery’s  Milling machine

Q: indoor design dry C and 25°C resp

A:

Q: Which one of given options is true? O Work surface after machining process transforms into machined…

A: Solution:

Q: the use of machines

A: Belt Length At the point when the head and tail pulley are a similar size: L=(D+d)/2 x 3.1416+2CAt…

Q: CHA

A: For solution refer below images.

Q: Pa P, 40°- 2 ft -25° P1 each item to a choice:

A:

Q: 2- A gear pump with a rotational

A: Gear Pump: A gear pump pumps fluid through displacement, and it does so by the meshing of gears.…

Q: 2. What is the quality of the exit st Answers:

A:

Q: 3- List two reason, to keep low pressure drop across the production system.

A: Pressure drop is used to characterize the reduction in air pressure from the compressor discharge to…

Q: systems use compressed

A: Pneumatic System

Q: Confined

A: given Identify actions required before approving Start of Work in a Confined Space.

Q: ceilings

A: Sea level maximum R/C condition Lift coefficient for maximum rate of climb CL=-TW+TW2+12CD,OK2K…

Q: how did you get the 3038Pa in static pressure?

A:

Q: A) What are the requirements for a good boiler

A: Requirements for a good boiler:

Q: Q2: For an air conditioning system, the compressor should not be started if the condenser an is not…

A:

Q: 16)In which process Catcher is used

A: Catcher is used in abrasive water jet machining According to question option c is absolutely correct

Q: D, =2-in Schedule 40 Branch I K=5 for open valve K= 10 for open valve Branch 2 D,= 4-in Schedule 40

A: here pipe in parallel connection, For parallel connection, Qtotal = Qupper + Qlower Htotal = Hupper…

Q: fluids. For the system containing water and oil, show

A: capillary pressure is a power because of differentials between liquid densities in a stone that can…

Q: onentially distributed service time. The average number of the will be

A: Given:Arrival rate of customers, λ=8 /hrservice rate,μ=606=10 /hr

Q: Sir, you need to explain the process for the production.

A: In the given drawing, to make the same profile of the workpiece, Firstly we have to take a circular…

Q: Need three views

A: According to the details provided in the question, we need to find three views.

Q: Blocked suction cylinder unloading is accomplished byA. keeping the suction valve closed.B. closing…

A: given; Blocked suction cylinder unloading is accomplished by

Q: Draw the set-up for dehydration and clearing.

A: Draw the diagram for the clearing and the dehydration process.

Q: Dons at C, ar 2"

A:

Q: What would happen if a hydronic system was installed without an expansion tank? A. The relief valve…

A: The relief valve would constantly go off.

Q: A 4 stroke 4 cylinder car engine of 4 L. What will be the swept volume of each engine?

A: Given:A 4 stroke four cylinder  has a swept volume of 4litre(L)Since nothing else is mentioned we…

Q: Load 1. TV NOOT

A:

Q: "N" JOBS- “3" MACHINE

A: Where Machine G is - A+B=8+5=13 10+6=16 6+2=8 7+3=10 11+4=15 And Where H - B+C 5+4=9 . .

Q: Draw pressure diagrams

A:

Q: f the desc oth of cut rations

A: Chip forming ;

Q: (a) Explain in detail the main difference between the drop platform truck and drop center baggage…

A: A platform truck is a flat sheet of metal that has wheels on the bottom and a handle on the back,…

Q: Insulation -Lead shot W To Control knob Thermal reservoir explain about the picture about…

A: