Give the following and encode it please. This is not a writing assignmentGiven =Required =Formula =Solution =Answer = The surface of the water in a storage tank is 30 m above a water faucet in the kitchen of a house, Fig.Calculate the difference in water pressure between the faucet and the surface of the water in the tank.The density of the water is 1x10³ kgm3"Figure 18. Pressure at a FaucetAh =30 mApproach – Water is practically incompressible, so p is constant even for a Ah = 30 when used inequation AP = pg Ah. Only Ah matters; we can ignore the "route" of the pipe and its bends.Note: The height h is sometimes called the pressure head. In the figure, the head of water is 30 m at thefaucet. The very different diameters of the tank and faucet don't affect the result – only pressure does.

Name: Give the following and encode it please. This is not a writing assignm
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: Give the following and encode it please. This is not a writing assignmentGiven =Required =Formula =Solution =Answer = The surface of the water in a storage tank is 30 m above a water faucet in the kitchen of a house, Fig.Calculate the difference in w

The pressure in a given fluid can be calculated in the following manner, P=FA where, F, is the force…

Science

Physics

The surface of the water in a storage tank is 30 m above a water faucet in the kitchen of a house, Fig. Calculate the difference in water pressure between the faucet and the surface of the water in the tank. The density of the water is 1x10³ k9. Figure 18. Pressure at a Faucet Ah = 30 m 田田田| Approach - Water is practically incompressible, so p is constant even for a Ah = 30 when used in equation AP = pg Ah. Only Ah matters; we can ignore the "route" of the pipe and its bends. Note: The height h is sometimes called the pressure head. In the figure, the head of water is 30 m at the faucet. The very different diameters of the tank and faucet don't affect the result – only pressure does.

The surface of the water in a storage tank is 30 m above a water faucet in the kitchen of a house, Fig. Calculate the difference in water pressure between the faucet and the surface of the water in the tank. The density of the water is 1x10³ k9. Figure 18. Pressure at a Faucet Ah = 30 m 田田田| Approach - Water is practically incompressible, so p is constant even for a Ah = 30 when used in equation AP = pg Ah. Only Ah matters; we can ignore the "route" of the pipe and its bends. Note: The height h is sometimes called the pressure head. In the figure, the head of water is 30 m at the faucet. The very different diameters of the tank and faucet don't affect the result – only pressure does.

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter11: Fluid Statics

Section: Chapter Questions

Problem 23PE: Show that the total force on a rectangular dam due to the water behind it increases with the square...

See similar textbooks

Similar questions

Find the gauge and absolute pressures in the balloon and peanut jar shown in Figure 11.16, assuming the manometer connected to the balloon uses water whereas the manometer connected to the jar contains mercury. Express in units of centimeters of water for the balloon and millimeters of mercury for the jar, taking h=0.0500 m for each. Figure 11.16 An open-tube manometer has one side open to the atmosphere. (a) Fluid depth must be the same on both sides, or the pressure each side exerts at the bottom will be unequal and there will be flow from the deeper side. (b) A positive gauge pressure Pg=hg transmitted to one side of the manometer can support a column of fluid of height h. (c) Similarly, atmospheric pressure is greater than a negative gauge pressure Pg by an amount hg .The jar's rigidity prevents atmospheric pressure from being transmitted to the peanuts.
What must be the contact area between a suction cup (completely evacuated) and a ceiling if the cup is to support the weight of an 80.0-kg student?
A trash compactor can compress its contents to 0.350 times their original volume. Neglecting mass of air expelled, by what factor is the density of be rubbish increased?
Explain why the fluid reaches equal levels on either side of a manometer if both sides are open to the atmosphere, even if the tubes are of different diameters.
What force must be exerted on the master cylinder of a hydraulic lift to support the weight of a 2000-kg car (a large car) resting on the slave cylinder? The master cylinder has a 2.00-cm diameter and the slave has a 24.0-cm diameter.
Pascal’s Principle and Hydraulics 59. How much pressure is transmitted in the hydraulic system considered in Example 14.3? Express your answer in atmospheres.
How do you convert pressure units like millimeters of mercury, centimeters of water, and inches of mercury into units like newtons per meter squared without resorting to a table of pressure conversion factors?
Concrete is pumped from a cement mixer to the place it is being lad, instead of being carried wheelbarrows. The flow rate is 200 L/min through a 50.0-m-long, 8.00-cm-diameter hose, and he pressure it the pump is 8.00106 N/m2. (a) Calculate the resistance of the hose. (b) What is the viscosity of the concrete, assuming the flow is laminar? (c) How much power is being supplied, assuming the point of use is at the same level as the pump? You may neglect the power supplied to increase be concrete's velocity.
Suppose you have a wind speed gauge like the pitot tube shown in Figure 14.32. By what factor must wad speed increase to double the value of h in the manometer? Is independent of be moving fluid and be fluid the Figure 14.32 Measurement of fluid speed on Bernoulli’s principle. (a) A manometer is connected to two tubes close together and small enough not to disturb the flow. Tube 1 is open at the end facing the flow. A dead spot having zero speed is created there. Tube 2 has an opening on the side, so the fluid has a speed v across; thus, pressure there drops. The difference in pressure at the manometer is 12v22 , so h is proportional to . 12v22 (b) This type of velocity measuring device is a Prandtl tube, also known as a pitot tube.
Gasoline is piped underground from refineries to major users. The flow rate is 3.00102m3/s (about 500 gal/min), viscosity of gasoline is 3.00102m3/s , and its density is 680 kg/m3. (a) What minimum diameter must be pipe have if the Reynolds number is to be less 2000? (b) What pressure difference must be along each kilometer of be pipe to maintain flow rate?
Why is it difficult to swim under water in the Great Salt Lake?
How would you determine the density of an irregularly shaped rock?