The system of pipe transports water at 68°F, consists of two branches as shown in Figure (1). Branch ABDC has a diameter of 0.5 in, whereas branch AEFGHC has a diameter of 1 in. If a pump provides an inlet flow at A of 0.15 ft/s, determine the flow through each branch. Take = 0.00008 ft. The system is in the horizontal plane. The loss coefficients for the elbow and the tee along the branch are 0.9 and 1.8, respectively. The diameters at A and C are the same. Take pw = 1.937 V 10.4×10-64

The system of pipe transports water at 68°F, consists of two branches as shown in Figure (1). Branch ABDC has a diameter of 0.5 in, whereas branch AEFGHC has a diameter of 1 in. If a pump provides an inlet flow at A of 0.15 ft/s, determine the flow through each branch. Take = 0.00008 ft. The system is in the horizontal plane. The loss coefficients for the elbow and the tee along the branch are 0.9 and 1.8, respectively. The diameters at A and C are the same. Take pw = 1.937 V 10.4×10-64

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure represents a stream of water in a pipe. If the distribution of velocities in a section is given by v (see picture) where beta is a constant, r is the radial distance to the axis, and v is the velocity a at distance r from the axis, determine the flow rate Q.S
Water circulates through the Venturi tube shown at 80°F. If an ideal flow is considered (without energy loss), determine the flow rate, the velocity in the pipe, and the velocity of contraction. The 9 in measurement is from center to center of the manometric tube.
A vessel is being filled with water through an inlet at section 1 having a diameter of 40 mm and a faucet at section 3. The velocity at section 1 is given as 5 m/s, while the discharge at section 3 is given as 0.012 m^3/ s. Assume constant water level. Use 60 mm for the diameter of the outlet at section 2. A. What is the discharge at section 2? B. What is exit velocity at section 2? C. If the water level varies and the velocity at section 2 is 8m/s find the rate of change when d is equal to 1000mm?
As given in the figure, the water flowing into a tank at a constant speed will make the tank in 5 minutes h = It fills up to a height of 3 m. The long side of the rectangular warehouse is 2 m and short If the side is 1.5 m, the water at 30 ° C flowing from the 0.2 m diameter pipe at point A Calculate its average velocity as [m / s] and its flow rate as [kg / s]. (b) Water at 0.5 m / s It flows into the pipe at a constant average velocity. In this framework, h = 3 m deep warehouse The relationship between the time required to fill (t) and the pipe diameter at point A (D) Determine. (Take the width of the warehouse as 1.5 m). Plot the graph of t (minutes) vs.D (m). (D; Let it be located on the horizontal axis as 0.05 m, 0.1 m, 0.15 m, 0.20 m and 0.25 m).
The diameters of a pipe at the sections 1 and 2 are 0.1 m and 0.15 m respectively Find the discharge through the pipe if the velocity of water flowing through the pipe at section 1 is 5 m/s.
Water at 40 degrees C is flowing from A to B through the system shown below. Determine the volumetric flow rate of the water if the vertical distance between the surfaces of the two reservoirs is 10 m. The elbows are standard. ( roughness for the ductile iron pipe = 0.061 mm or 0.0024 in)
From the following figure, determine: a) the flow rate through the pipe b) the velocity in the pipe c) the pressure at points A, B, C, D. d) outline the line of motor head for this situation . fluid is
The diameter of the pipe at point B is larger than at point A. - At which point is the water speed greater? Point B Point A It is the same at both points. Cannot be determined from the information given.
Reservoir A and B have elevations of 100 m and 160 mm respectively. A pump is installed near reservoir A to pump water from A to B. The rate of flow in the pipes is 650 L/s and the pipe length of 1000 m with a diameter of 600 mm. If C= 120 what is the Energy added by the pump?
The flow carried by pipe below discharges into the open atmosphere. If the pipe length is 300 m, diameter is 150 mm and roughness of 0.0025 mm, write the equation(s) required to determine the maximum discharge.
A Venturi meter has a pressure gauge attached as shown in the figure. If the flow velocity of water in the 1-inch-diameter section is 25 ft / s, determine the distance and
The figure below shows a turbine with an inlet pipe and a draft tube. If the efficiency of the turbine is only 80 percent and the discharge of the water is 1000 litres per second. Calculate: (a) the power developed by the turbine: (b) The reading of the gauge G: