The system shown in the figure is used to accurately measure the pressure changes when the pressure is increased by AP in the water pipe. When Ah-91 mm, what is the change in pipe pressure? Water Pipe Glycerin, SG-1.26 D-30mm The change in pipe pressure is Ak d-3mm Pa

The system shown in the figure is used to accurately measure the pressure changes when the pressure is increased by AP in the water pipe. When Ah-91 mm, what is the change in pipe pressure? Water Pipe Glycerin, SG-1.26 D-30mm The change in pipe pressure is Ak d-3mm Pa

Name: The system shown in the figure is used to accurately measure the pres
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The system shown in the figure is used to accurately measure the pressure changes when the pressure is increased by AP in thewater pipe. When Ah=91 mm, what is the change in pipe pressure?WaterPipeGlycerin, SG-1.26D-30mmThe change in pipe pressure i

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 14RQ: Atmospheric pressure at sea level under standard conditions is ______inches of mercury (Hg) or_____...

See similar textbooks

Similar questions

the figure below shows a water pipe where a pressure tap is being carried out. At the site, the specific gravity of water Ywater=10,000 N/m^3 and the specific gravity of mercury is UHg=136,000 N/m^3. Find the gauge pressure in pipe A. Where h1=50mm; h2=20mm; h3=30mm; h4=20mm
The fluid in a manometer tube is 60% water and 40% alcohol (SG = 0.8). What is the manometer fluid height difference if a 6 psi pressure is applied across the two ends of a manometer?
Two tubes are mounted to the roof of a car. One tube points to the front of the car and the other points to the rear. the tubes are connected to a manometer filled with fluid of sg 0.60. When the height difference is 2 inches. What is the car speed in mph?
In the figure shown below, an open manometer is connected to a pipe to measure the pressure at A. Fluid at A is oil of s.g. oil = 0.85 , the value of (x = 334 mm) and the value of ( y = 400 mm) to obtain the pressure intensity as gauge pressure as well as absolute pressure. Take Patm = 1.01396 bar , and the manometer fluid s.g. Hg=13.6 2-Gage pressure at A (PAgage) is equal to -----------? 1-Absolute pressure at A (PAabs) is equal to -----------?both answer in kN/m^2
The fluid in a manometer tube is 60 % water and 40 % alcohol (S.G. = 0.83). What is the manometer fluid height difference (in ft) if a 13.6 psi pressure is applied across the two ends of a manometer?
The pressure drop across a filter in a water supply line is measured using a Utube manometer filled with carbon tetrachloride (1.595 specific gravity). If the upstream pressure is 18.6 psig, what is the absolute pressure in the pipe after the filter? (in kPa)
At one point in a pipeline the water's speed is 3.00 m/sand the gauge pressure is 5.00×10^4 Pa a) Find the gauge pressure at a second point in the line, 11.0 mm lower than the first, if the pipe diameter at the second point is twice that at the first. Express your answer in kilopascals.
The gauge pressure in a liquid at a depth of 2.7m is 55.8 kPa. What is the gauage pressure kPa in the same liquid at a depth of 6.4m. I need right solution with clear calculations.
Two tubes are mounted to the roof of a car. One tube points to the front of the car and the other points to the rear. the tubes are connected to a manometer filled with fluid of sg 0.60. When the height difference is 2 inches. What is the car speed in mph? Provide a clear and complete solution
Parts A-C and Label them Question : Water flows downward in a pipe at 45°, as shown in figure below. The pressure drop p1 − p2 is partly due to gravity and partly due to friction. The mercury manometer reads a 6-in height difference. Part [A] - What is the total pressure drop p1 − p2 in lbf/in2? Part [B] - What is the pressure drop due to friction only between 1 and 2 in lbf/in2? Part [C] - What is the pressure drop due to gravity only between 1 and 2 in lbf/in2?
The system shown in the figure is used to accurately measure the pressure changes when the pressure is increased by ΔP in the water pipe. When Dh = 70 mm, what is the change in the pipe pressure?
Oil (SG = 0.92) fills both pipe "A" and pipe "B" which are vertically separated by 24-inches. The two pipes are connected by a mercury (SG=13.6) manometer showing a 12-inch pressure differential. What are the specific weight, density, and specific volume of the oil? What is the difference in pressure between Pipe "A" and Pipe "B" (in psi)?