The T section shown is the cross-section of a beam formed by joining two rectangular pieces of steel together. The beam is subjected to a maximum shearing force of 60 kN. Use NA = 34 mm from the %3D top and INA = 10.57 × 106 mm4, determine the shearing stress at the neutral axis. 200 mm 40 mm 100 mm 20 mm 3.28 MPa 2.38 MPa

The T section shown is the cross-section of a beam formed by joining two rectangular pieces of steel together. The beam is subjected to a maximum shearing force of 60 kN. Use NA = 34 mm from the %3D top and INA = 10.57 × 106 mm4, determine the shearing stress at the neutral axis. 200 mm 40 mm 100 mm 20 mm 3.28 MPa 2.38 MPa

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
What is the area of the tube? What is the total length of the median line? What will be the result shear flow of the object? The shearing stress value will be The angle of twist will be
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at top of the beam section at 3.09 from the support. (MPa) Properties: Beam width = 259 mmBeam height = 447 mmPu = 63.85 kNSpan of the beam = 10 mPrestressing force = 502 kNeccentricity = 96 mm
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at 3.41 from the support. (MPa) Properties: Beam width = 206 mmBeam height = 495 mmPu = 66.2 kNSpan of the beam = 11 mPrestressing force = 335 kNeccentricity = 105 mm
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The butt diameter is 450 mm and the tip diameter (the top of the pole) is 320 mm. The weight of the pole, cross arms, and wires is 33 kN. Assuming the pole transmits the load as a point load, find the change in vertical stress in kPa at 2 m depth. a. 17.8 b.393.9 c.63.0 d.3.9
The following rigid structure ABCD is supported by a hinge at B and two bars at C and D. The applied load is 100 kN. The data is shown in the table. Determine: The stress in each bar. Answ: 27.01 MPa, 328.01 MPa The vertical displacement at the point where the load is applied. Answ: 0.9403 mm. The rotation at point B. Answ: 0.001069 rad. The horizontal displacement 400 mm below point B. Answ: 0.42741 mm.
The internal shear force V at a certain section of a steel beam is 80 kN, and the moment of inertia is 64,867,500 mm4. Determine the horizontal shear stress at point H, which is located L = 17 mm below the centroid. 58.9 MPa 42.7 MPa 39.6 MPa 35.2 MPa 31.2 MPa
Find. (1) Maximum bending stress at point B (2). Calculate deflection at point B.
The beam is to be cut lengthwise along both sides, as shown in the figure. Nap made of a material that has an allowable shear stress of tperm = 75 MPa, determine the shear force maximum allowable V that can be applied before and after making the cut.
The following beam is supported by an aluminum bar at C, a steel bar at B, and a brass bar at D. The distance b is equal to 50 mm. The data is shown in the table:If the maximum rotation that can occur at point A is 0.25 radians clockwise, determine: a. The maximum force P that can be applied. Answ: 28347.97 kNb. The normal stress in the aluminum, steel, and brass bars. Answ: 25 000 MPa, 17500 MPa, 25937.5 MPa