The tank shown is being filledwith water by two one-Tank area A,dimensional inlets. Air istrapped at the top of the tank.The water height is h.Pa(a) Find an expression for thechange in water height dhldt.HPw(b) Compute dhldt if D,=1 in,D2=3 in, V=3 ft/s, V,=2 ft/s,and A,= 2 ft², assuming waterat 20°CFixed CS

The control volume encircle the tank and cuts through the two inlets The flow with in is unsteady So…

The tank shown is being filled with water by two one- dimensional inlets. Air is Tank area A, trapped at the top of the tank. The water height is h. a (a) Find an expression for the change in water height dhldt. (b) Compute dhldt if D=1 in, D=3 in, V=3 ft/s, V=2 ft/s, and A,= 2 ft?, assuming water H h Pw (2) %3D at 20°C Fixed CS

The tank shown is being filled with water by two one- dimensional inlets. Air is Tank area A, trapped at the top of the tank. The water height is h. a (a) Find an expression for the change in water height dhldt. (b) Compute dhldt if D=1 in, D=3 in, V=3 ft/s, V=2 ft/s, and A,= 2 ft?, assuming water H h Pw (2) %3D at 20°C Fixed CS

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The system in the figure is at 70°C (SG = 0.983). Determine the pressure at point C. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: Ib/ft?
3.Water flows from a tank through 22 meters of 150–mmdiameter pipe and then discharges into air as shown in the figure. The flow of water in the pipe is 120 L/s.Assume n = 0.013 and neglect minor losses. a. Find the velocity of flow in the pipe in m/s. b. Determine the total head loss in the pipe in meters. c. Calculate the pressure at the top of the tank in kPa.
Compute the gage and absolute pressures at point m. Fluid A is air and fluid B is mercury.
1. A rectangular gate AB hinged at A has a width 2.0 m perpendicular to the paper, has a negligible weight. The water surface remains at the top of the gate. Determine the vertical component of the hinge force in kN to maintain equilibrium. Write your answer to the nearest three decimal places. Use unit weight of water 9.80 kN/m^3.
Q1(a) Explain the difference between wetting fluid and non-wetting fluid (b) The 60m X 60m rectangular gate shown in Figure Q1(b) has its top edge located 3m vertically below the water surface. The gate is to be opened from its lower edge by applying a normal force by the shaft. Determine the minimum force F required to open the water gate. (Ignore Patm in all your calculations)
Water flows from a tank through 160 feet of 4 inches diameter pipe and then discharges into air as shown in the Figure. The flow of water in the pipe is 12cfs. Assume n=0.013 and neglect minor losses. Determine the following: (a) The velocity of flow in the pipe in fps. (b) The total head lost in the pipe in feet. (c) The pressure at the top of the tank in psi.
Fluid mechanics, pipe problem: The pipe shown has a 180o vertical bend in it. The diameter, D, is 1 foot, and the pressure at the center of the pipe is 15psig. If the flow in the bend is 20 cfs, what external force will be necessary to hold the bend in place against the action of the water? The bend weighs 200 lbf, and the volume of the bend is 3 ft3. Assume the Bernoulli Equation applies. Rhowater= 62.4lb/ft3).
In figure 3 compute the pressure head difference between m and n, in feet of fluid A, when: A. Fluid A is gasoline (sp gr 0.715), the gage liquid is mercury, and z = 47.77 in B. Fluid A is oil (sp gr 0.908), the gage liquid is water, and z = 27.77 in C. Fluid A is sea water (w = 64.0), the gage liquid has a specific gravity of 2.95, and z = 57.77
A venturi-meter having an entrance diameter of 300 mm and throat diameter 200 mm is used to measure the volume of a water flowing through a pipe. The coefficient of discharge is 0,96. The reading in the venturi-meter head is 175 mm of water. Determine the pressure difference in Pascals.
Based on the provided differential-type manometer, calculate the difference in the pressure between points A and B (as in Δp = pA - pB = ?). SG of oil is 0.8 . Provide solution in finding the height.
The pump shown in the figure adds 15 ft of head to the water being pumped when the flow rate is 1.5 ft/s and the pressure at point A is 2 lb/in. Determine the friction factor for the pipe.
A pump draws water from reservoir A and lifts it to a higher reservoir B, as shown in Figure P4.2.6. Thehead loss from A to the pump is four times the velocity head in the pipe, and the head loss fromthe pump to B is seven times the velocity head. The pressure head at the inlet of the pump is .Compute the pressure head the pump must deliver. Why is the pressure head the pump must delivergreater than , the elevation difference between the two reservoirs? Draw the EGL and HGL.