The thermodynamic process of a substance when it passes through device changes in a constant pressure process. If the initial and final volumes of the substance are 0.4m3and 0.13m3respectively, what is the magnitude of work is required for this process? Is it done on or done by the system? Draw a schematic diagram,andthen plot the state/s and process, whichever is applicable in a t-sdiagram

Q: The tension member is fastened together using two bolts, one on each side of the member as shown.…

A: given that: Two bolts of 12 mm diameter are used. Maximum allowable shear stress is 80 MPa. Maximum…

Q: An experimental device imparts a force of magnitude F = 36 lb to the front edge of the rim at A to…

A: Moment about O = -34.62 lb-ft Moment about B = -91.36 lb-ft

Q: Determine (a) percent clearance, (b) P, V, and T at each corner of the cycle, (c) QAT, (d) e, and…

A:

Q: Q1/ Choose the correct answer (True or False) False O True AutoCAD provides nine ways to draw an arc…

A:

Q: For the structure shown in Fig.(2), determine the tension in cable ABD and the reaction at C when…

A:

Q: Calculate the moment Mg of the 605-N force about the bolt at B. Simplify your work by first…

A:

Q: 1. Determine the magnitude and direction with respect to the +x axis on the reaction at A and at C.…

A:

Q: 2.( , The blank for the spool shown in the figure below is to be sand cast out of A-319, an aluminum…

A:

Q: the work done (W12) in (kJ) is Below 10 Between 10 and 30 Between 30 and 50 Between 50 and 70 O…

A:

Q: A mercury-filled U-tube manometer is fastened to a fuel tank. The mercury level on the manometer's…

A: Given : height of mercury level in other end, h = 40 cm = 0.4 m To find : tanks gage pressure

Q: An experimental device imparts a force of magnitude F = 41 lb to the front edge of the rim at A to…

A:

Q: The maximum temperature in : the cycle (in degree Kelvin) is Otto cycle has a compression ratio of…

A: 1) The Maximum cycle temprature =2676.470k OPTION 3 - BETWEEN 2500-2750K 2) The Exhaust temperature…

Q: The cords suspend the two buckets in the equilibrium position as shown in . Bucket A has a weight of…

A: Given, Using Lami's theorem and drawing FBD,

Q: 5. A student living in a 4 m x 6 m x 6 m dormitory room turns on her 150 watts fan before she leaves…

A: The given data in the problem is represented in the following attached image:

Q: A 2-stroke engine that works based on the diesel cycle admits air conditioning 100kPa and 280K. The…

A:

Q: Q7) Determine the reactions at the supports A and C of the compound beam. Assume A is fixed, B is a…

A:

Q: the work done (W12) in (kJ) is Below 10 O Between 10 and 30 O Between 30 and 50 O Between 50 and 70…

A:

Q: 3. In a test to determine the bulk modulus of a liquid it was found that as the absolute press was…

A:

Q: An insulation material of thermal conductivity k = 0.05 is sandwiched between thin metal sheets of…

A: Given:Thermal conductivity of insulation, k=0.05 W/m.KInside air temperature, Ti=300oCInner side…

Q: 2-26 Determine the energy required to accelerate an 800- kg car from rest to 100 km/h on a level…

A: m = mass of the car = 800 kg The car starts from rest Final velocity of the car is 100 km/h It is…

Q: Saturated air at 15°C flows to a heater at the rate of 0.76 m³/s. Heat is transferred to the air at…

A: Write the properties of saturated air at 15 oC. h=cPT=1.005283=284.415 kJ/kgAnd,ρ=1.2 kg/m3

Q: For real diffusers the exit velocity can be practically equal to zero. O True O False

A: Diffuser is a device which decelerates the flow.

Q: During heating and humidification process briefly describes how the psychrometric properties below…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked.…

Q: The three forces are applied to the bracket. Determine the minimum value for the magnitude of force…

A: Introduction: When the force is applied to an angle, the resultant force has two force components,…

Q: A hollow circular shaft with OD 1.5 and ID 1.25 and made of steel with an allowable shear stress of…

A: Write the expression for pure torsion equation. TJ=τr

Q: An experimental device imparts a force of magnitude F = 36 lb to the front edge of the rim at A to…

A:

Q: 399. Replace the force and couple moment system acting on the overhang beam by a resultant force,…

A:

Q: ump is fitted to 100 m pipeline that connects reservoir A reservoir B. The diameter of the pipe is…

A: Given:Length of the pipeline, l=100 mDiameter of the pipe, d=200 mmfriction factor, f=0.02Design…

Q: A particle moves along a straight line with a velocity in millimeters per second given by v=…

A:

Q: A student drove to the university from her home and noted that the odometer reading of her car…

A: Given data: d1=12 kmt1=18 mind2=10.3 kmθ=25° douth of east Need to determine the average speed and…

Q: 6. A hydraulic lift (see below) of the type commonly used for greasing automobiles consists of a…

A: Introduction: A hydraulic lift is used to lift the object by using the force created when the…

Q: Problem 5 (a) A 10-mm-diameter Brinell hardness in- denter produced an indentation 2.50 mm in di-…

A:

Q: Ammonia contained in a piston-cylinder assembly, initially saturated vapor at 0˚F, undergoes an…

A:

Q: The deceleration of the mass center G of a car during a crash test is measured by an accelerometer…

A: Given DataX=0.8m

Q: The normal shock wave moves tow the back tank at underexpansion fl regime during the operation of…

A:

Q: mes checks the pressure on his front left tire, and it reads 25 pound per square inch (psi). His…

A: pressure required=32psi current pressure=25psi

Q: Draw Iron - Iron Carbide Phase diagram and show the following: 4- Types of ferrous alloys on…

A: given; iron-iron carbide phase diagram;

Q: The flow carried by the pipe below discharges into the open atmosphere. If the pipe length is 300 m,…

A: Given: L = 300 m D = 150 mm = 0.15 m  ∈=0.0025 mm ∆Z=Z1-Z2=16 m

Q: What is the difference between  lb·mass and lb · force ?______________     A. They are the same.…

A:

Q: A υ = 2π υ )(α-3 + 2a3)

A: Write the total area of the cylinder. A=πdL+2π4d2=πdL+π2d2

Q: the initial mass (m1) in (kg) is A rigid 0.15 m³ tank contains air at 0.8 MPa, 200°C. A valve on the…

A:

Q: A ferry transports tourists among three islands. It sails from the first island to the second…

A:

Q: In thehydroelectric power plant, water enters the turbine nozzles at 700 kPa absolute witha low…

A:

Q: The block in the figure has a weight of 400 lb and an applied force of 600 lb to the right. There is…

A: Given   Weight, W = 400 lb  Force, F = 600 lb Find   Magnitude

Q: Determine the natural frequency of a pendulum whose length is 41 ft. in Hz

A: Given Data: Pendulum length l = 41 ft The period for the oscillation of pendulum is given by…

Q: The graph shows the displacement-time history for the rectilinear motion of a particle during an…

A:

Q: Do you think heating-humidification process is of utmost importance for Comfort AC system for…

A: Philippines is situated in the tropical region in the world map so the country has frequently…

Q: Determine the resultant force of the system shown below. 2241 200 lb 60⁰ 12 390 lb 300 lb -X

A:

Q: There are 300 cubic meter/min of atmospheric air initially at 25 C wet bulb temperature and 60 % RH…

A: Given: Flow rate of the atmospheric air→Qa=300 m3/min=5 m3/s Wet bulb temperature of the atmospheric…

Q: 3-93. Replace the loading by a single resultant force. Specify where the force acts, measured from…

A: Draw the free-body diagram of the beam.